TRACKING DATA MESSAGE RECOMMENDED STANDARD CCSDS 503.0-B-1 BLUE BOOK November 2007 CCSDS RECOMMENDED STANDARD FOR TRACKING DATA MESSAGE AUTHORITY Issue: Recommended Standard, Issue 1 Date: November 2007 Location: Washington, DC, USA This document has been approved for publication by the Management Council of the Consultative Committee for Space Data Systems (CCSDS) and represents the consensus technical agreement of the participating CCSDS Member Agencies. The procedure for review and authorization of CCSDS Recommendations is detailed in the Procedures Manual for the Consultative Committee for Space Data Systems, and the record of Agency participation in the authorization of this document can be obtained from the CCSDS Secretariat at the address below. This document is published and maintained by: CCSDS Secretariat Space Communications and Navigation Office, 7L70 Space Operations Mission Directorate NASA Headquarters Washington, DC 20546-0001, USA STATEMENT OF INTENT The Consultative Committee for Space Data Systems (CCSDS) is an organization officially established by the management of its members. The Committee meets periodically to address data systems problems that are common to all participants, and to formulate sound technical solutions to these problems. Inasmuch as participation in the CCSDS is completely voluntary, the results of Committee actions are termed Recommended Standards and are not considered binding on any Agency. This Recommended Standard is issued by, and represents the consensus of, the CCSDS members. Endorsement of this Recommendation is entirely voluntary. Endorsement, however, indicates the following understandings: Whenever a member establishes a CCSDS-related standard, this standard will be in accord with the relevant Recommended Standard. Establishing such a standard does not preclude other provisions which a member may develop. Whenever a member establishes a CCSDS-related standard, that member will provide other CCSDS members with the following information: -- The standard itself. -- The anticipated date of initial operational capability. -- The anticipated duration of operational service. Specific service arrangements shall be made via memoranda of agreement. Neither this Recommended Standard nor any ensuing standard is a substitute for a memorandum of agreement. No later than five years from its date of issuance, this Recommended Standard will be reviewed by the CCSDS to determine whether it should: (1) remain in effect without change; (2) be changed to reflect the impact of new technologies, new requirements, or new directions; or (3) be retired or canceled. In those instances when a new version of a Recommended Standard is issued, existing CCSDS-related member standards and implementations are not negated or deemed to be non-CCSDS compatible. It is the responsibility of each member to determine when such standards or implementations are to be modified. Each member is, however, strongly encouraged to direct planning for its new standards and implementations towards the later version of the Recommended Standard. FOREWORD This document is a Recommended Standard for tracking data messages and has been prepared by the Consultative Committee for Space Data Systems (CCSDS). The tracking data message described in this Recommended Standard is the baseline concept for tracking data interchange applications that are cross-supported between Agencies of the CCSDS. This Recommended Standard establishes a common framework and provides a common basis for the format of tracking data exchange between space agencies. It allows implementing organizations within each Agency to proceed coherently with the development of compatible derived standards for the flight and ground systems that are within their cognizance. Derived Agency standards may implement only a subset of the optional features allowed by the Recommended Standard and may incorporate features not addressed by this Recommended Standard. Through the process of normal evolution, it is expected that expansion, deletion or modification to this document may occur. This Recommended Standard is therefore subject to CCSDS document management and change control procedures, as defined in the Procedures Manual for the Consultative Committee for Space Data Systems. Current versions of CCSDS documents are maintained at the CCSDS Web site: http://www.ccsds.org/ Questions relating to the contents or status of this document should be addressed to the CCSDS Secretariat at the address indicated on page i. At time of publication, the active Member and Observer Agencies of the CCSDS were: Member Agencies - Agenzia Spaziale Italiana (ASI)/Italy. - British National Space Centre (BNSC)/United Kingdom. - Canadian Space Agency (CSA)/Canada. - Centre National d'Etudes Spatiales (CNES)/France. - Deutsches Zentrum fur Luft- und Raumfahrt e.V. (DLR)/Germany. - European Space Agency (ESA)/Europe. - Federal Space Agency (FSA)/Russian Federation. - Instituto Nacional de Pesquisas Espaciais (INPE)/Brazil. - Japan Aerospace Exploration Agency (JAXA)/Japan. - National Aeronautics and Space Administration (NASA)/USA. Observer Agencies - Austrian Space Agency (ASA)/Austria. - Belgian Federal Science Policy Office (BFSPO)/Belgium. - Central Research Institute of Machine Building (TsNIIMash)/Russian Federation. - Centro Tecnico Aeroespacial (CTA)/Brazil. - Chinese Academy of Sciences (CAS)/China. - Chinese Academy of Space Technology (CAST)/China. - Commonwealth Scientific and Industrial Research Organization (CSIRO)/ Australia. - Danish National Space Center (DNSC)/Denmark. - European Organization for the Exploitation of Meteorological Satellites (EUMETSAT)/Europe. - European Telecommunications Satellite Organization (EUTELSAT)/Europe. - Hellenic National Space Committee (HNSC)/Greece. - Indian Space Research Organization (ISRO)/India. - Institute of Space Research (IKI)/Russian Federation. - KFKI Research Institute for Particle & Nuclear Physics (KFKI)/Hungary. - Korea Aerospace Research Institute (KARI)/Korea. - MIKOMTEK: CSIR (CSIR)/Republic of South Africa. - Ministry of Communications (MOC)/Israel. - National Institute of Information and Communications Technology (NICT)/ Japan. - National Oceanic and Atmospheric Administration (NOAA)/USA. - National Space Organization (NSPO)/Taiwan. - Naval Center for Space Technology (NCST)/USA. - Space and Upper Atmosphere Research Commission (SUPARCO)/Pakistan. - Swedish Space Corporation (SSC)/Sweden. - United States Geological Survey (USGS)/USA. DOCUMENT CONTROL Document Title Date Status CCSDS Tracking Data Message, November Original issue 503.0-B-1 Recommended Standard, Issue 1 2007 CCSDS RECOMMENDED STANDARD FOR TRACKING DATA MESSAGE CONTENTS Section Page 1 INTRODUCTION.......................................................... 1-1 1.1 PURPOSE ............................................................ 1-1 1.2 SCOPE AND APPLICABILITY ............................................ 1-1 1.3 CONVENTIONS AND DEFINITIONS......................................... 1-2 1.4 STRUCTURE OF THIS DOCUMENT.......................................... 1-3 1.5 REFERENCES ......................................................... 1-4 2 OVERVIEW.............................................................. 2-1 2.1 GENERAL ............................................................ 2-1 2.2 THE TRACKING DATA MESSAGE (TDM) BASIC CONTENT ...................... 2-1 3 TRACKING DATA MESSAGE STRUCTURE AND CONTENT........................... 3-1 3.1 GENERAL ............................................................ 3-1 3.2 TDM HEADER ......................................................... 3-3 3.3 TDM METADATA ....................................................... 3-5 3.4 TDM DATA SECTION (GENERAL SPECIFICATION) ........................... 3-19 3.5 TDM DATA SECTION KEYWORDS .......................................... 3-23 4 TRACKING DATA MESSAGE SYNTAX ......................................... 4-1 4.1 GENERAL ............................................................ 4-1 4.2 TDM LINES .......................................................... 4-1 4.3 TDM VALUES ......................................................... 4-2 4.4 UNITS IN THE TDM ................................................... 4-3 4.5 COMMENTS IN A TDM .................................................. 4-4 5 SECURITY.............................................................. 5-1 5.1 GENERAL ............................................ 5.2 SECURITY CONCERNS RELATED TO THIS RECOMMENDED STANDARD ............................................................... 5-1 5.3 POTENTIAL THREATS AND ATTACK SCENARIOS ............................. 5-2 5.4 CONSEQUENCES OF NOT APPLYING SECURITY TO THE TECHNOLOGY ............................................................. 5-2 5.5 DATA SECURITY IMPLEMENTATION SPECIFICS ............................. 5-2 ANNEX A VALUES FOR TIME_SYSTEM AND REFERENCE_FRAME (NORMATIVE) ............................................................ A-1 ANNEX B ITEMS FOR AN INTERFACE CONTROL DOCUMENT (INFORMATIVE) .......................................................... B-1 ANNEX C ABBREVIATIONS AND ACRONYMS (INFORMATIVE)........................ C-1 ANNEX D EXAMPLE TRACKING DATA MESSAGES (INFORMATIVE) ................... D-1 ANNEX E INFORMATIVE REFERENCES (INFORMATIVE) ........................... E-1 ANNEX F RATIONALE FOR TRACKING DATA MESSAGES (INFORMATIVE) .......................................................... F-1 ANNEX G TDM SUMMARY SHEET (INFORMATIVE) ................................ G-1 Figure D-1 TDM Example: One-Way Data .......................................... D-1 D-2 TDM Example: One-Way Data w/Frequency Offset ....................... D-2 D-3 TDM Example: Two-Way Frequency Data for Doppler Calculation ........ D-3 D-4 TDM Example: Two-Way Ranging Data Only ............................. D-4 D-5 TDM Example: Three-Way Frequency Data .............................. D-5 D-6 TDM Example: Four-Way Data ......................................... D-6 D-7 TDM Example: One S/C, X-up, S-down, X-down, Ka-down, Three Segments D-7 D-8 TDM Example: Angles, Range, Doppler Combined in Single TDM ......... D-8 D-9 TDM Example: Range Data with TIMETAG_REF=TRANSMIT .................. D-9 D-10 TDM Example: Differenced Doppler Observable ....................... D-10 D-11 TDM Example: Delta-DOR Observable.................................. D-11 D-12 TDM Example: Angle Data Only ...................................... D-12 D-13 TDM Example: Media Data Only ...................................... D-13 D-14 TDM Example: Meteorological Data Only ............................. D-14 D-15 TDM Example: Clock Bias/Drift Only ................................ D-15 Table 3-1 TDM Structure ...................................................... 3-2 3-2 TDM Header ......................................................... 3-3 3-3 TDM Metadata Section ............................................... 3-7 3-4 Tracking Data Record Generic Format ................................ 3-19 3-5 Summary Table of TDM Data Section Keywords (Alpha Order) ........... 3-24 3-6 Summary Table of TDM Data Section Keywords (Category Order) ........ 3-25 F-1 Primary Requirements ............................................... F-2 F-2 Heritage Requirements .............................................. F-3 F-3 Desirable Characteristics .......................................... F-3 1 INTRODUCTION 1.1 PURPOSE 1.1.1 This Tracking Data Message (TDM) Recommended Standard specifies a standard message format for use in exchanging spacecraft tracking data between space agencies. Such exchanges are used for distributing tracking data output from routine interagency cross-supports in which spacecraft missions managed by one agency are tracked from a ground station managed by a second agency. The standardization of tracking data formats facilitates space agency allocation of tracking sessions to alternate tracking resources. This Recommended Standard has been developed via consensus of the Navigation Working Group of the CCSDS Mission Operations and Information Management Services (MOIMS) area. 1.1.2 This document includes requirements and criteria that the message format has been designed to meet. For exchanges where these requirements do not capture the needs of the participating Agencies another mechanism may be selected. 1.2 SCOPE AND APPLICABILITY 1.2.1 This Recommended Standard contains the specification for a Tracking Data Message designed for applications involving tracking data interchange between space data systems. Tracking data includes data types such as Doppler, transmit/received frequencies, range, angles, Delta-DOR, DORIS, PRARE, media correction, weather, etc. The rationale behind the design of the message is described in annex F and may help the application engineer construct a suitable message. It is acknowledged that this version of the Recommended Standard may not apply to every single tracking session or data type; however, it is desired to focus on covering approximately the '95% level' of tracking scenarios, and to expand the coverage in future versions as experience with the TDM is gained. 1.2.2 This message is suited to inter-agency exchanges that involve automated interaction. The attributes of a TDM make it primarily suitable for use in computer-to-computer communication because of the large amount of data typically present. The TDM is self-contained, with no additional information required beyond that specified in an Interface Control Document (ICD) written jointly by the service provider and customer agency. 1.2.3 Definition of the accuracy pertaining to any particular TDM is outside the scope of this Recommended Standard and should be specified via an Interface Control Document (ICD) between data exchange participants. 1.2.4 This Recommended Standard is applicable only to the message format and content, but not to its transmission. The method of transmitting the message between exchange partners is beyond the scope of this document and should be specified in the ICD. Message transmission could be based on a CCSDS data transfer protocol, file based transfer protocol such as SFTP, stream-oriented media, or other secure transmission mechanism. In general, the transmission mechanism must not place constraints on the technical data content of a TDM. 1.2.5 There are some specific exclusions to the TDM, as listed below: 1.2.5.1 Satellite Laser Ranging (SLR) 'Fullrate' and/or 'Normal Points' format (sometimes referred to as 'Quicklook'), which are already transferred via a standardized format documented at http://ilrs.gsfc.nasa.gov/; 1.2.5.2 Exchanges of raw Global Navigation Satellite System (GNSS) data, which is standardized via the RINEX format ( http://gps.wva.net/html.common/rinex.html); 1.2.5.3 Global Positioning Satellite (GPS) navigation solutions, which are standardized via the SP3 format (http://www.ngs.noaa.gov/GPS/GPS.html);1 1.2.5.4 Optical data from navigation cameras (pixel based, row-column, etc.); 1.2.5.5 LIDAR data (which may include a laser range finder); however, such data could conceivably be transferred via TDM with a 'RANGE' keyword (see 3.5.2.6); and 1.2.5.6 Altimeter data; however, such data could conceivably be transferred via TDM with a 'RANGE' keyword (see 3.5.2.6). 1.2.6 Description of the message format based on the use of eXtensible Markup Language (XML) is detailed in an integrated XML schema document for all Navigation Data Message Recommendations: Attitude Data Messages (ADM), Orbit Data Messages (ODM), and Tracking Data Message (TDM). See reference [E8]. 1.3 CONVENTIONS AND DEFINITIONS 1.3.1 Conventions and definitions of navigation concepts such as reference frames, time systems, etc., are provided in reference [1]. 1.3.2 The following conventions apply throughout this Recommended Standard: - the words 'shall' and 'must' imply a binding and verifiable specification; - the word 'should' implies an optional, but desirable, specification; - the word 'may' implies an optional specification; - the words 'is', 'are', and 'will' imply statements of fact. ---------------------------------------------------------------------------- 1 It has been suggested that the statement regarding navigation solutions being standardized by SP3 is not correct, because SP3 prescribes equidistant data (ephemerides), which are in general not provided by each GPS/GNSS receiver. It was proposed that the navigation solution data (epoch, x, y, z, vx, vy, vz) should be provided in the TDM, with the velocities as optional values. However, this would require major changes to the TDM that are contrary to its intended purpose. As an alternative, the CCSDS Orbit Data Messages OEM (Orbit Ephemeris Message) (reference [4]) could be used to convey the navigation solution if all position and velocity components are transferred. The OEM is already set up to convey all the required values, and can be used to convey orbit reconstructions as well as orbit p redictions. ---------------------------------------------------------------------------- - The word 'participant' denotes an entity that has the ability to acquire or broadcast navigation messages and/or radio frequencies, for example, a spacecraft, a quasar, a tracking station, a tracking instrument, or an agency. - The term 'n/a' or 'N/A' denotes an attribute that is not applicable or not available. 1.3.3 The following conventions for unit notations apply throughout this Recommended Standard. Insofar as possible, an effort has been made to use units that are part of the International System of Units (SI Units); units are either SI base units, SI derived units, or units outside the SI that are accepted for use with the SI (see reference [8]). There are a small number of specific cases where units that are more widely used in the navigation community are specified, but every effort has been made to minimize these departures from the SI. %: per cent dBHz: decibels referenced to one Hz dBW: decibels referenced to one Watt deg: degrees of plane angle hPa: hectoPascal Hz: Hertz K: degrees Kelvin km: kilometers m: meters RU: range units s: seconds TECU: Total Electron Count Units 1.4 STRUCTURE OF THIS DOCUMENT 1.4.1 Section 2 provides a brief overview of the CCSDS-recommended Tracking Data Message (TDM). 1.4.2 Section 3 provides details about the structure and content of the TDM. 1.4.3 Section 4 provides details about the syntax used in the TDM. 1.4.4 Section 5 discusses security considerations for the TDM. 1.4.5 Annex A provides a normative list of approved values for selected TDM Metadata Section keywords. 1.4.6 Annex B lists a number of items that should be covered in interagency ICDs prior to exchanging TDMs on a regular basis. There are several statements throughout the document that refer to the desirability or necessity of such a document; this annex consolidates all the suggested ICD items in a single list. 1.4.7 Annex C is a list of abbreviations and acronyms applicable to the TDM. 1.4.8 Annex D shows how various tracking scenarios can be accommodated using the TDM, via several examples. 1.4.9 Annex E contains a list of informative references. 1.4.10 Annex F lists a set of requirements and desirable characteristics that were taken into consideration in the design of the TDM. 1.4.11 Annex G provides a TDM Summary Sheet, or 'Quick Reference'. 1.5 REFERENCES The following documents contain provisions which, through reference in this text, constitute provisions of this Recommended Standard. At the time of publication, the editions indicated were valid. All documents are subject to revision, and users of this Recommended Standard are encouraged to investigate the possibility of applying the most recent editions of the documents indicated below. The CCSDS Secretariat maintains a register of currently valid CCSDS Recommended Standards. [1] Navigation Data-Definitions and Conventions. Report Concerning Space Data System Standards, CCSDS 500.0-G-2. Green Book. Issue 2. Washington, D.C.: CCSDS, November 2005. [2] Information Technology-8-Bit Single-Byte Coded Graphic Character Sets-Part 1: Latin Alphabet No. 1. International Standard, ISO/IEC 8859-1:1998. Geneva:ISO, 1998. [3] Time Code Formats. Recommendation for Space Data System Standards, CCSDS 301.0-B-3. Blue Book. Issue 3. Washington, D.C.: CCSDS, January 2002. [4] Orbit Data Messages. Recommendation for Space Data System Standards, CCSDS 502.0-B-1. Blue Book. Issue 1. Washington, D.C.: CCSDS, September 2004. [5] Spacewarn Bulletin. Greenbelt, MD, USA: WDC-SI. [6] XML Schema Part 2: Datatypes. 2nd ed. P. Biron and A. Malhotra, eds. W3C Recommendation 28. n.p.: W3C, 2004. [7] IEEE Standard for Binary Floating-Point Arithmetic. IEEE Std 754-1985. New York: IEEE, 1985. [8] "The NIST Reference on Constants, Units, and Uncertainty." NIST Physics Laboratory. NOTE - Informative references are provided in annex E. OVERVIEW 2.1 GENERAL This section provides a high-level overview of the CCSDS recommended Tracking Data Message, a message format designed to facilitate standardized exchange of spacecraft tracking data between space agencies. 2.2 THE TRACKING DATA MESSAGE (TDM) BASIC CONTENT 2.2.1 The TDM is realized as a sequence of plain ASCII text lines (reference [2]), which may be in either a file format or a real-time stream. The content is separated into three basic types of computer data structure as described in section 3. The TDM architecture takes into account that some aspects of tracking data change on a measurement-by-measurement basis (data); some aspects change less frequently, but perhaps several times per track (metadata); and other aspects change only rarely, e.g., once per track or perhaps less frequently (header). The TDM makes it possible to convey a variety of tracking data used in the orbit determination process in a single data message (e.g., standard Doppler and range radiometrics in a variety of tracking modes, VLBI data, antenna pointing angles, etc.). To aid in precision trajectory modeling, additional ancillary information may be included within a TDM if it is desired and/or available (e.g., media corrections, meteorological data, clock data, and other ancillary data). Facilities for documenting comments are provided. 2.2.2 The Tracking Data Message in this version of the Recommended Standard is ASCII-text formatted. While binary-based tracking data message formats are computer efficient and minimize overhead during data transfer, there are ground-segment applications for which an ASCII character-based message is more appropriate. For example, ASCII format character-based tracking data representations are useful in transferring data between heterogeneous computing systems, because the ASCII character set is nearly universally used and is interpretable by all popular systems. In addition, direct human-readable dumps of text to displays, emails, documents or printers are possible without preprocessing. The penalty for this convenience is some measure of inefficiency (based on early tests, such penalty would be greatly reduced if the data is compressed for transmission). 2.2.3 The ASCII text in a TDM can be exchanged in either of two formats: a 'keywordvalue notation' format (KVN) or an XML format. The KVN formatted TDM is described in this document. Description of the message format based on XML is detailed in an integrated XML schema document for all Navigation Data Messages (reference [E8]). Exchange participants should specify in the ICD which TDM ASCII format will be exchanged, the KVN or the XML format. 2.2.4 Normally a TDM will contain tracking data for a single spacecraft participant, unless the tracking session is spacecraft-to-spacecraft in nature. If a tracking operation involves information from multiple spacecraft participants tracked from the ground, the data may be included in a single TDM by using multiple segments (see 3.1); or multiple TDMs may be used, one per spacecraft participant. 2.2.5 For a given spacecraft participant, multiple tracking data messages may be provided in a message exchange session to achieve the tracking data requirements of the participating agencies (e.g., launch supports with periodically delivered TDMs, or other critical events such as maneuvers, encounters, etc.). 2.2.6 Provisions for the frequency of exchange and special types of exchanges should be specified in an ICD. 3 TRACKING DATA MESSAGE STRUCTURE AND CONTENT 3.1 GENERAL 3.1.1 The TDM shall consist of digital data represented as ASCII text lines (see reference [2]) in KVN format (Keyword = Value Notation-see section 4). The lines constituting a TDM shall be represented as a combination of: a) a Header (see 3.2); b) a Metadata Section (data about data) (see 3.3); and c) a Data Section (tracking data represented as 'Tracking Data Records') (see 3.4). Optional comments may appear in specified locations in the Header, Metadata, and Data Sections (see 4.5). 3.1.2 Taken together, the Metadata Section and its associated Data Section shall be called a TDM Segment. 3.1.3 Each TDM shall have a Header and a Body. The TDM Body shall consist of one or more TDM Segments. There shall be no limit to the number of Segments in a given TDM Body, beyond practical constraints, as shown in table 3-1. Each Segment shall consist of a Metadata Section and a Data Section that consists of a minimum of one Tracking Data Record. Therefore, the overall structure of the TDM shall be: - TDM = Header + Body; - Body = Segment [+ Segment + ... + Segment]; - Segment = Metadata Section + Data Section; - Data Section = Tracking Data Record (TDR) [ + TDR + TDR ... + TDR]. CCSDS 503.0-B-1 Page 3-1 November 2007 Table 3-1: TDM Structure See PDF version of document for table. 3.1.4 The TDM shall consist of tracking data for one or more tracking participants at multiple epochs contained within a specified time range. (Note that the term 'participant' applies equally to spacecraft, quasars, tracking stations, and agency centers, as discussed in reference [1]. Thus there may exist Tracking Data Messages for which there is no applicable spacecraft.) Generally, but not necessarily, the time range of a TDM may correspond to a 'tracking pass'. 3.1.5 The TDM shall be easily readable by both humans and computers. 3.1.6 It shall be possible to exchange a TDM either as a real-time stream or as a file. 3.1.7 The TDM file naming scheme shall be agreed to on a case-by-case basis between the participating agencies, typically specified in an ICD. In general, the file name syntax and length must not violate computer constraints for those computing environments in use by Member Agencies for processing tracking data. 3.1.8 The method of exchanging TDMs shall be decided on a case-by-case basis by the participating agencies and documented in an ICD. The exchange method shall not constrain the tracking data content. 3.2 TDM HEADER 3.2.1 The TDM shall include a Header that consists of information that identifies the basic parameters of the message. The first Header line must be the first non-blank line in the message. 3.2.2 A description of TDM Header items and values is provided in table 3-2, which specifies for each item: - the keyword to be used; - a short description of the item; - examples of allowed values; and - whether the item is obligatory or not obligatory. 3.2.3 Only those keywords shown in table 3-2 shall be used in a TDM Header. The order of occurrence of the obligatory and optional KVN assignments shall be fixed as shown in table 3-2. Table 3-2: TDM Header See PDF version of document for table. 3.2.4 Each line in the TDM Header, with the exception of COMMENTs, shall have the following generic format: keyword = value 3.2.5 The TDM Header shall provide a CCSDS Tracking Data Message version number that identifies the format version; this is included to anticipate future changes and to provide the ability to extend the standard with no disruption to existing users. The version keyword is CCSDS_TDM_VERS and the value shall have the form of x.y where y is incremented for corrections and minor changes, and x is incremented for major changes. Version 1.0 shall be reserved for the initial version accepted by the CCSDS as an official Recommended Standard ('Blue Book'). Interagency testing of TDMs shall be conducted using version numbers less than 1.0 (e.g., '0.y'). Specific TDM versions that will be exchanged between agencies should be documented via the ICD. 3.2.6 The TDM Header shall include the CREATION_DATE keyword with the value set to the Coordinated Universal Time (UTC) when the data was created (file creation time if in file format, or first data point in stream), as specified in reference [3] (ASCII Time Code A or B). 3.3 TDM METADATA 3.3.1 GENERAL 3.3.1.1 The TDM shall include at least one Metadata Section that contains configuration details (metadata) applicable to the Data Section in the same TDM Segment. The information in the Metadata Section aligns with the tracking data to provide descriptive information (typically, the metadata is the type of information that does not change frequently during a tracking session). 3.3.1.2 Each line in the TDM Metadata Section, with the exception of COMMENTs, shall have the following generic format: keyword = value 3.3.1.3 A single TDM Metadata Section shall precede each Data Section. 3.3.1.4 When there are changes in the values assigned to any of the keywords in the Metadata Section, a new Segment must be started (e.g., mode change from one-way to two-way tracking). 3.3.1.5 The first and last lines of a TDM Metadata Section shall consist of the META_START and META_STOP keywords, respectively. These keywords are used to facilitate parsing. 3.3.1.6 Table 3-3 specifies for each Metadata item: - the keyword to be used; - a short description of the item; - a list of required values or examples of allowed values; and - whether the item is obligatory or not obligatory. The column marked 'N/E' will contain an 'N' if the column marked 'Normative Values / Examples' contains normative values, and will contain an 'E' if the column contains example values that are non-normative. For normative values, a fully enumerated set of values may be provided, or the contents of table 3-3 may be a sample of values that are fully enumerated in an annex. In this latter case, the necessary annex is identified. 3.3.1.7 Only those keywords shown in table 3-3 shall be used in a TDM Metadata Section. Obligatory items shall appear in every TDM Metadata Section. Items that are not obligatory may or may not appear in any given TDM Metadata Section, at the discretion of the data producer, based on the requirements of the data and its intended application (see annex G for a TDM Summary Sheet that illustrates the relationships between data types and metadata). For most metadata keywords there is no default value; where there is a default value, it is specified at the end of the 'Description' section for the given keyword. If a keyword is not present in a TDM, and a default value is defined, the default shall be assumed. 3.3.1.8 The order of occurrence of the obligatory and optional KVN assignments shall be fixed as shown in table 3-3. 3.3.1.9 The Metadata Section shall describe the participants in a tracking session using the keyword 'PARTICIPANT_n'. There may be several participants associated with a tracking data session (the number of participants is always greater than or equal to one, and generally greater than or equal to two). The 'n' in the keyword is an indexer. The indexer shall not be the same for any two participants in a given Metadata Section. 3.3.1.10 The value associated with any given PARTICIPANT_n keyword may be a ground tracking station, a spacecraft, a quasar catalog name; or may include non-traditional objects, such as landers, rovers, balloons, etc. The list of eligible names that is used to specify participants should be documented in the ICD. Subsections 3.3.2 through 3.3.2.7 provide an explanation of the tracking modes and participant numbers. Participants may generally be listed in any order. 3.3.1.11 In this version of the TDM, the maximum number of participants per segment shall be five. If more than five participants are defined (i.e., PARTICIPANT_6 +), then special arrangements between exchange participants are necessary. These arrangements should be documented in an ICD. Note that although the restriction to five participants may appear to be a constraint it is probably not, because of other aspects of the TDM structure. Five participants easily allow the user to describe the great majority of tracking passes. In some cases there may be 'critical event' tracking sessions in which a single spacecraft is tracked by a large number of antennas, such that the total number of participants appears to be six or more. However, because of the nature of the 'PATH' keyword, several TDM Segments would be required to describe the full set of tracking data. For the critical event example scenario just given, one TDM Segment would be used to describe the two-way connection, and one additional segment would be required for each three-way connection; it would not be possible to provide a single 'PATH' statement that would convey the multiple signal paths. Table 3-3: TDM Metadata Section See PDF version of document for table. 3.3.2 MODE AND PATH SETTINGS FOR TYPICAL TRACKING SESSIONS NOTE - The following subsections discuss possible relationships between the 'MODE', 'PATH', and 'PARTICIPANT_n' keywords. This discussion is provided in order to facilitate the implementation of TDM generation for typical tracking sessions (e.g., one-way, two-way, three-way, etc.). Annex G supplies recommendations of the metadata keywords that should be used to properly describe the tracking data of various types depending on the settings of the MODE and PATH keywords, with allowance for characteristics of the uplink frequency (if applicable). 3.3.2.1 One-Way Data 3.3.2.1.1 The setting of the 'MODE' keyword shall be 'SEQUENTIAL'. 3.3.2.1.2 For one-way data, the signal path generally originates at the spacecraft transmitter, so the spacecraft's participant number shall be the first number in the value assigned to the PATH keyword. The receiver, which may be a tracking station or another spacecraft, shall be represented by the second number in the value of the PATH keyword. EXAMPLES - 'PATH=1,2' indicates transmission from PARTICIPANT_1 to PARTICIPANT_2; 'PATH=2,1' indicates transmission from PARTICIPANT_2 to PARTICIPANT_1. NOTE - See figures D-1 and D-2 for example TDMs containing one-way tracking data. 3.3.2.2 Two-Way Data 3.3.2.2.1 The setting of the 'MODE' keyword shall be 'SEQUENTIAL'. 3.3.2.2.2 For two-way data, the signal path originates at a ground antenna ( or a 'first spacecraft'), so the uplink (or crosslink) transmit participant number shall be the first number in the value assigned to the PATH keyword. The participant number of the transponder onboard the spacecraft to which the signal is being uplinked shall be the second number in the value assigned to the PATH keyword. The third entry in the PATH keyword value shall be the same as the first (two way downlink is received at the same participant which transmits the uplink/crosslink). Both PARTICIPANT_1 and PARTICIPANT_2 may be spacecraft as in the case of a spacecraft-spacecraft exchange. EXAMPLES - 'PATH=1,2,1' indicates transmission from PARTICIPANT_1 to PARTICIPANT_2, with final reception at PARTICIPANT_1; 'PATH=2,1,2' indicates transmission from PARTICIPANT_2 to PARTICIPANT_1, with final reception at PARTICIPANT_2. NOTE - See figures D-3, D-4, and D-9 for example TDMs containing two-way tracking data. 3.3.2.3 Three-Way Data 3.3.2.3.1 The setting of the 'MODE' keyword shall be 'SEQUENTIAL'. 3.3.2.3.2 For three-way data, the signal path originates with a ground station (uplink antenna), so the participant number of the uplink station shall be the first entry in the value assigned to the PATH keyword. The participant number of the transponder onboard the spacecraft to which the signal is being uplinked shall be the second number in the value assigned to the PATH keyword. The participant number of the downlink antenna shall be the third number in the value assigned to the PATH keyword. 3.3.2.3.3 For three-way data, the first and last numbers in the value assigned to the PATH keyword must be different. EXAMPLES - 'PATH=1,2,3' indicates transmission from PARTICIPANT_1 to PARTICIPANT_2, with final reception at PARTICIPANT_3. NOTE - See figure D-5 for an example TDM containing three-way tracking data. 3.3.2.4 N-Way Data 3.3.2.4.1 One-way, two-way, and three-way tracking cover the bulk of tracking sequences. However, four-way and greater (n-way) scenarios are possible (e.g., via use of one or more relay satellites). These may be accomplished via the sequence assigned to the PATH keyword. 3.3.2.4.2 The setting of the 'MODE' keyword shall be 'SEQUENTIAL'. 3.3.2.4.3 The value assigned to the PATH keyword shall convey the signal path among the participants followed by the signal; e.g., 'PATH=1,2,3,2,1' and 'PATH=1,2,3,4' represent two different four-way tracking signal paths. 3.3.2.4.4 In this version of the TDM, the maximum number of participants per segment shall be five. If more than five participants are defined (i.e., PARTICIPANT_6 +), then special arrangements shall be made; these should be specified in the ICD. NOTE - See figure D-6 for an example TDM containing four-way tracking data. 3.3.2.5 Differenced Modes and VLBI Data 3.3.2.5.1 Differenced data and VLBI data may also be exchanged in a Tracking Data Message. Differenced data can include differenced Doppler and differenced range (see references [E3] and [E4]). 3.3.2.5.2 The setting of the 'MODE' keyword shall be 'SINGLE_DIFF'. 3.3.2.5.3 When the MODE is 'SINGLE_DIFF', two path keywords, 'PATH_1' and 'PATH_2', shall be used to convey the signal paths that have been differenced. 3.3.2.5.4 When the mode is 'SINGLE_DIFF', the observable is calculated by subtracting the value achieved for the measurement using PATH_1 from the value achieved using PATH_2, i.e., PATH_2 - PATH_1. Only the final observable shall be communicated via the TDM. 3.3.2.5.5 If the TDM contains differenced Doppler shift data, the 'RECEIVE_FREQ' keyword shall be used for the observable (the 'RECEIVE_FREQ' keyword is a Data Section keyword not yet described in the text-see 3.5.2.7). 3.3.2.5.6 If the TDM contains two-way or three-way differenced Doppler data, then a history of the uplink frequencies shall be provided with the TRANSMIT_FREQ_n keyword in order to process the data correctly (the 'TRANSMIT_FREQ_n' keyword is a Data Section keyword not yet described in the text-see 3.5.2.8). 3.3.2.5.7 If differenced range is provided, the 'RANGE' keyword shall be used for the observable (the 'RANGE' keyword is a Data Section keyword not yet described in the text- see 3.5.2.6). 3.3.2.5.8 If the TDM contains differenced data collected during a Delta-Differential One Way Range (Delta-DOR) session with a spacecraft, then the DOR keyword shall be used for the observable (the 'DOR' keyword is a Data Section keyword not yet described in the text-see 3.5.3.2). 3.3.2.5.9 If the TDM contains differenced data collected during a VLBI session with a quasar, then the VLBI_DELAY keyword shall be used for the observable (the 'VLBI_DELAY' keyword is a Data Section keyword not yet described in the text-see 3.5.3.3). NOTE - See figures D-10 and D-11 for example TDMs containing single differenced tracking data. 3.3.2.6 Angle Data Angle data is applicable for any tracking scenario where MODE=SEQUENTIAL is specified, but is based on pointing with respect to the two final participants only (e.g., spacecraft downlink to an antenna, direction of a participant measured by a navigation camera, etc.). NOTE - See figures D-8 and D-12 for example TDMs containing angle data. 3.3.2.7 Media, Weather, Ancillary Data 3.3.2.7.1 When all the data in a TDM Segment is media related, weather related, or ancillary-data related, then the use of the MODE keyword may or may not apply as discussed below. 3.3.2.7.2 Data of this type may be relative to a reference location within the tracking complex; in this case the methods used to extrapolate the measurements to other antennas should be specified in the ICD. In the case where a reference location is used, there shall be only one participant (PARTICIPANT_1), which is the reference antenna, and the MODE keyword shall not be used. This case corresponds to tropospheric correction data, zenith ionospheric correction data, and weather data. 3.3.2.7.3 When ionospheric charged particle delays are provided for a line-of-sight between the antenna and a specific spacecraft, the participants include both the antenna and the spacecraft, the MODE should be set to 'SEQUENTIAL', and a standard PATH statement should be used. NOTE - See figures D-13 through D-15 for example TDMs containing tracking data of these types. 3.4 TDM DATA SECTION (GENERAL SPECIFICATION) 3.4.1 The Data Section of the TDM Segment shall consist of one or more Tracking Data Records. Each Tracking Data Record shall have the following generic format: keyword = timetag measurement NOTE - More detail on the generic format of a Tracking Data Record is shown in table 3-4. Table 3-4: Tracking Data Record Generic Format See PDF version of document for table. 3.4.2 Each Tracking Data Record must be provided on a single line. 3.4.3 Each Tracking Data Record shall contain a value that depends upon the data type keyword used. The value shall consist of two elements: a timetag and a tracking observable (a measurement or calculation based on measurements); either without the other is useless for tracking purposes. Hereafter, the term 'measurement' shall be understood to include calculations based on measurements as noted above. 3.4.4 At least one blank character must be used to separate the timetag and the observable in the value associated with each Tracking Data Record. 3.4.5 Applicable keywords and their associated characteristics are detailed in 3.5. 3.4.6 There shall be no obligatory keywords in the Data Section of the TDM Segment, with the exception of 'DATA_START' and 'DATA_STOP', because the data presented in any given TDM is dependent upon the characteristics of the data collection activity. 3.4.7 The Data Section of the TDM Segment shall be delineated by the 'DATA_START' and 'DATA_STOP' keywords. These keywords are intended to facilitate parsing, and will also serve to advise the recipient that all the Tracking Data Records associated with the immediately preceding TDM Metadata Section have been received (the rationale for including this is that data volumes can be very large, so knowing when the data ends is desirable). The TDM recipient may process the 'DATA_STOP' keyword as a 'local' end-of-file marker. 3.4.8 Tracking data shall be tagged according to the value of the 'TIME_SYSTEM' metadata keyword. 3.4.9 Interpretation of the timetag for transmitted data is straightforward; it is the transmit time. Interpretation of the timetag for received data is determined by the values of the 'TIMETAG_REF', 'INTEGRATION_REF', and 'INTEGRATION_INTERVAL' keywords, as applicable (see table 3-3 and 3.5.2.7). For other data types (e.g., meteorological, media, clock bias/drift), the timetag represents the time the measurement was taken. 3.4.10 In general, no required ordering of Tracking Data Records shall be imposed, because there are certain scenarios in which data are collected from multiple sources that are not processed in strictly chronological order. Thus it may only be possible to generate data in chronological order if it is sorted post-pass. However, there is one ordering requirement placed on Tracking Data Records; specifically, in any given Data Section, the data for any given keyword shall be in chronological order. Also, some TDM creators may wish to sort tracking data by keyword rather than by timetag. Special sorting requirements should be specified in the ICD. 3.4.11 Each keyword/timetag combination must be unique within a given Data Section (i.e., a given keyword/timetag combination shall not be repeated in the same set of Tracking Data Records). 3.4.12 The time duration between timetags may be constant, or may vary, within any given TDM. 3.4.13 Every tracking instrument shall have a defined reference location. This reference location shall not depend on the observing geometry. The tracking instrument locations should be conveyed via an ICD. The ICD information should include a complete description of the station locations and characteristics, including the antenna coordinates with their defining system, plate motion, and the relative geometry of the tracking point and cross axis of the antenna mount, accommodations for antenna tilt to avoid keyhole problems, etc. The station location could be provided via an OPM (reference [4]). Antenna geometry would be necessary for exceptional cases, where the station location is not fixed during track, for example. 3.4.14 The measurement shall be converted to an equipment-independent quantity; e.g., frequencies shall be reported at the 'sky level' (i.e., actual transmitted/received frequencies, unless the FREQ_OFFSET keyword is used in the metadata). It should not be necessary for the data recipient to have detailed information regarding the internal network of the data producer. 3.4.15 Tracking data is normally subject to a number of corrections, as described in the following paragraphs. 3.4.15.1 The tracking data measurements shall be corrected with the best estimate of all known instrument calibrations, such as path delay calibrations between the reference point and the tracking equipment, if applicable. NOTE - These measures should reduce the requirement for consumers of tracking data to have detailed knowledge of the underlying structure of the hardware/software system that performed the measurements. 3.4.15.2 Tracking data should be corrected for ground delays only. The corrections that have been applied may be specified to the message recipient via use of the optional 'CORRECTION_*' keywords in the metadata. NOTE - The 'TRANSMIT_DELAY' and 'RECEIVE_DELAY' keywords do not represent 'ground corrections' per se. They are meant to convey gross factors that do not change from pass-to-pass. However, if exchange partners agree via the ICD, 'TRANSMIT_DELAY' and 'RECEIVE_DELAY' could be removed from the measurements. It is generally operationally inconvenient for the producer to treat these values as corrections because of the possible requirement to alter uplink timetags; thus these delays are best handled in orbit determination post-processing. Modifying timetags to account for these delays also complicates the use of differenced measurements. It is thus more straightforward to allow the recipient to process these delays rather than to correct the data prior to exchange. 3.4.15.3 If correction values are indicated via any of the 'CORRECTION_*' keywords, then the TDM producer must indicate whether these correction values have or have not been applied to the tracking data. This indication is accomplished via the use of the metadata keyword 'CORRECTIONS_APPLIED'; this metadata item must have a value of 'YES' or 'NO'. 3.4.15.4 Media corrections (ionosphere, troposphere) should not be applied by the TDM producer; media corrections may be applied by the TDM recipient using the data conveyed in the STEC, TROPO_WET, and TROPO_DRY Data Section keywords. 3.4.15.5 The party that will perform any applicable spin corrections should be specified in the ICD (most appropriate party may be the party that operates the spacecraft). 3.4.15.6 Special correction algorithms that are more complex than a simple scalar value should be specified in the ICD. 3.4.15.7 Any other corrections applied to the data shall be agreed by the service provider and the customer Agencies and specified in an ICD. 3.4.16 All data type keywords in the TDM Data Section must be from 3.5, which specifies for each keyword: - the keyword to be used; - applicable units for the associated values; - a reference to the text section where the keyword is described in detail. NOTES 1 The standard tracking data types are extended to cover also some of the ancillary data that may be required for precise orbit determination work. Subsection 3.5 identifies the most frequently used data and ancillary types. 2 See annex D for detailed usage examples. 3 Annex G supplies recommendations of the metadata keywords that should be used to properly describe the tracking data of various types depending on the settings of the MODE and PATH keywords, with allowance for characteristics of the uplink frequency (if applicable). 3.5 TDM DATA SECTION KEYWORDS 3.5.1 OVERVIEW This subsection describes each of the keywords that may be used in the Data Section of the TDM Segment. In general, there is no required order in the Data Section of the TDM Segment. Exceptions are the 'DATA_START' and 'DATA_STOP' keywords, which must be the first and last keywords in the Data Section, respectively. For ease of reference, table 3-5 containing all the keywords sorted in alphabetical order is shown immediately below. Table 3-6 repeats the information from table 3-5 in category order. Descriptive information about the keywords is shown starting in 3.5.2. The remainder of this subsection is organized according to the class of data to which the keyword applies (e.g., all the signal related keywords are together, all media related keywords are together, etc.). Table 3-5: Summary Table of TDM Data Section Keywords (Alpha Order) See PDF version of document for table. Table 3-6: Summary Table of TDM Data Section Keywords (Category Order) See PDF version of document for table. 3.5.2 SIGNAL RELATED KEYWORDS 3.5.2.1 CARRIER_POWER The CARRIER_POWER keyword conveys the strength of the radio signal transmitted by the spacecraft as received at the ground station or at another spacecraft (e.g., in formation flight). This reports the strength of the signal received from the spacecraft, in decibels (referenced to 1 watt). The unit for the CARRIER_POWER keyword is dBW. The value shall be a double precision value, and may be positive, zero, or negative. The value is based on the last leg of the signal path (PATH keyword), e.g., spacecraft downlink to an antenna. Additional TDM Segments should be used for each participant if it is important to know the carrier power at each participant in a PATH that involves more than one receiver. 3.5.2.2 DOPPLER_INSTANTANEOUS The value associated with the DOPPLER_INSTANTANEOUS keyword represents the instantaneous range rate of the spacecraft. The observable may be one-way, two-way or three-way. The value shall be a double precision value and may be negative, zero, or positive. Units are km/s. In order to ensure that corrections due to the ionosphere and solar plasma are accurately applied, the transmit frequency and receive frequency should be supplied when this data type is exchanged. NOTE - The DOPPLER_INSTANTANEOUS assumes a fixed uplink frequency (or one with small RTLT errors), and thus should not be used in cases where there is a deep space ramped uplink (the TRANSMIT_FREQ and RECEIVE_FREQ keywords should be used instead). 3.5.2.3 DOPPLER_INTEGRATED The value associated with the DOPPLER_INTEGRATED keyword represents the mean range rate of the spacecraft over the INTEGRATION_INTERVAL specified in the Metadata Section. The timetag and the time bounds of the integration interval are determined by the TIMETAG_REF and INTEGRATION_REF keywords. The observable may be one-way, two-way or three-way. For one-way data, the observable is the mean range rate of the spacecraft over the INTEGRATION_INTERVAL. For two-way and three-way data, the ICD should specify whether the observable is the calculated mean range rate, or half the calculated mean range rate (due to the signal's having traveled to the spacecraft and back to the receiver). The value shall be a double precision value and may be negative, zero, or positive. Units are km/s. In order to ensure that corrections due to the ionosphere and solar plasma are accurately applied, the transmit frequency and receive frequency should be supplied when this data type is exchanged. NOTE - The DOPPLER_INTEGRATED assumes a fixed uplink frequency (or one with small RTLT errors), and thus should not be used in cases where there is a deep space ramped uplink (the TRANSMIT_FREQ and RECEIVE_FREQ keywords should be used instead). 3.5.2.4 PC_N0 The value associated with the PC_N0 keyword shall be the carrier power to noise spectral density ratio (Pc/No). The units for PC_N0 shall be dBHz. The value shall be a double precision value. 3.5.2.5 PR_N0 The value associated with the PR_N0 keyword shall be the ranging power to noise spectral density ratio (Pr/No). The units for PR_N0 shall be dBHz. It shall be a double precision value, and may be positive, zero, or negative. 3.5.2.6 RANGE The value associated with the RANGE keyword is the range observable. The values represent measurements from ambiguous ranging systems, differenced range, skin radar, proximity radar, or similar radar. The units for RANGE shall be as determined by the 'RANGE_UNITS' metadata keyword (i.e., either 'km', 's', or 'RU'). The 'RANGE_UNITS' metadata keyword should always be specified, but if it is not, the default (preferred) value shall be 'km'. If different range units are used by the tracking agency (e.g., 'DSN range units'), the definition of the range unit should be described in the ICD. Note that for many applications, proper processing of the RANGE will require a time history of the uplink frequencies. If ambiguous range is provided (i.e., the RANGE_MODULUS is non-zero), then the RANGE does not represent the actual range to the spacecraft; a calculation using the RANGE_MODULUS and the RANGE observable must be performed. If differenced range is provided (MODE = SINGLE_DIFF), the 'RANGE' keyword shall be used to convey the difference in range. The value shall be a double precision value, and is generally positive (exceptions to this could occur if the data is a differenced type, or if the observable is a one-way pseudorange). NOTE - The TDM specifically excludes Satellite Laser Ranging (SLR), which is already transferred via an internationally standardized format documented at http://ilrs.gsfc.nasa.gov/. 3.5.2.7 RECEIVE_FREQ (and RECEIVE_FREQ_n) 3.5.2.7.1 The RECEIVE_FREQ keyword shall be used to indicate that the values represent measurements of the received frequency. It is suitable for use with deep space ramped uplink if the TRANSMIT_FREQ is also exchanged. The keyword is indexed to accommodate a scenario in which multiple downlinks are used; it may also be used without an index where the frequency cannot be associated with a particular participant (e.g., in the case of a differenced Doppler shift measurement). The value associated with the RECEIVE_FREQ keyword shall be the average frequency observable over the INTEGRATION_INTERVAL specified in the metadata, at the measurement timetag. The interpretation of the timetag shall be determined by the combined settings of the TIMETAG_REF, INTEGRATION_REF, and INTEGRATION_INTERVAL keywords (see table 3-3 for a description of how the settings of these values affect the interpretation of the timetag). Correlation between the RECEIVE_FREQ and the associated TRANSMIT_FREQ may be determined via the use of an a priori estimate and should be resolved via the orbit determination process. The units for RECEIVE_FREQ shall be Hertz (Hz). The value shall be a double precision value (generally positive, but could be negative or zero if used with the 'FREQ_OFFSET' metadata keyword). 3.5.2.7.2 Using the RECEIVE_FREQ, the instantaneous Doppler measurement is calculated as follows: See PDF version of document for equation. where 'Dm' is the Doppler measurement, 'Ft' is the transmitted frequency, 'tr' is the transponder ratio (tr=1 for one-way), and 'Fr' is the RECEIVE_FREQ. For integrated Doppler, the Doppler measurement is calculated as follows, where t is the timetag, and .t is the value assigned to the INTEGRATION_INTERVAL keyword: See PDF version of document for equations. The limits of integration are determined by the INTEGRATION_REF keyword in the metadata; the constant a in the equation has the value -1.5, 0, or 1.5 for the INTEGRATION_REF values of 'END', 'MIDDLE', or 'START', respectively (see reference [E4]). See PDF version of document for table. 3.5.2.7.3 If differenced Doppler is provided, the non-indexed 'RECEIVE_FREQ' keyword shall be used to convey the difference in Hz. 3.5.2.7.4 The transponder ratios used for interagency exchanges should be specified in the ICD if they are always constant. They may also be specified in the metadata by using the TURNAROUND_NUMERATOR and TURNAROUND_DENOMINATOR keywords. 3.5.2.7.5 The equation for four-way Doppler, if it is to be exchanged, should be in the ICD since the four-way connections tend to be implementation dependent. 3.5.2.8 TRANSMIT_FREQ_n The TRANSMIT_FREQ keyword shall be used to indicate that the values represent measurements of a transmitted frequency, e.g., from an uplink operation. The TRANSMIT_FREQ keyword is indexed to accommodate scenarios in which multiple transmitters are used. The value associated with the TRANSMIT_FREQ_n keyword shall be the starting frequency observable at the timetag. The units for TRANSMIT_FREQ_n shall be Hertz (Hz). The value shall be a positive double precision value. The turnaround ratios necessary to calculate the predicted receive frequency may be specified using the TURNAROUND_NUMERATOR and TURNAROUND_DENOMINATOR metadata keywords, or may be specified in the ICD. In the case of software defined radios, the metadata keywords may be preferable as the ratios can change with some regularity and it is necessary to get the applicable ratio with the tracking data. Usage notes: when the data mode is one-way (i.e., MODE=SEQUENTIAL, PATH=1,2 or PATH=2,1), the signal is at the beacon frequency transmitted from the spacecraft. If a given spacecraft has more than one transponder, then there should be unique names specified in the ICD for each transponder (e.g., Cassini_S, Cassini_X, Cassini_Ka). If a TDM is constructed with only transmit frequencies, then the MODE is 'SEQUENTIAL' and the PATH keyword defines the signal path. Generally the timetag for the TRANSMIT_FREQ_n keywords should be the time that the signal was transmitted. For quasar DOR, the TRANSMIT_FREQ_n is the interferometer reference frequency at the receive time (thus TIMETAG_REF=RECEIVE for this case). If the transmit frequency varies in the TDM segment, then the TRANSMIT_FREQ_RATE_n keyword should be used to convey the frequency rate between transmit frequencies (see next section); otherwise, the frequency rate is assumed to be zero and a step function results. 3.5.2.9 TRANSMIT_FREQ_RATE_n The value associated with the TRANSMIT_FREQ_RATE_n keyword is the linear rate of change of the frequency starting at the timetag and continuing until the next TRANSMIT_FREQ_RATE timetag (or until the end of the data). The units for TRANSMIT_FREQ_RATE_n shall be Hertz-per-second (Hz/s). The value shall be a double precision value, and may be negative, zero, or positive. If the TRANSMIT_FREQ_RATE_n is not specified, it is assumed to be zero (i.e., constant frequency). 3.5.3 VLBI AND DELTA-DOR RELATED KEYWORDS 3.5.3.1 Overview In VLBI, a signal source is measured simultaneously using two receivers in different antenna complexes, achieving a long baseline (up to thousands of kilometers). The signals recorded at the two complexes are correlated and differenced to produce the observable, which may be further processed by navigation software. 'Delta-DOR' sessions are a VLBI application in which the antenna slews from a spacecraft source to a quasar source and back to the spacecraft during the tracking pass. This sequence may occur multiple times. There are two data keywords that relate to VLBI and Delta-DOR measurements, and several metadata keyword settings are applicable (MODE=SINGLE_DIFF, PATH_1 and PATH_2). 3.5.3.2 DOR The observable associated with the DOR keyword represents the range measured via PATH_2 minus the range measured via PATH_1. The timetag is the time of signal reception via PATH_1. This data type is normally used for the spacecraft observable in a Delta-DOR measurement. The range is either one-way, two-way, or three-way, depending on the values of the PARTICIPANT_n and PATH keywords. TRANSMIT_FREQ_n shall provide the spacecraft beacon frequency if one-way, or the transmit frequency at the uplink station if two-way or three-way, at the signal transmission time. The DOR measurement shall be a double precision value. Units shall be seconds. 3.5.3.3 VLBI_DELAY The observable associated with the VLBI_DELAY keyword represents the time of signal arrival via PATH_2 minus the time of signal arrival via PATH_1. The timetag is the time of signal reception via PATH_1. This data type is normally used for the quasar observable in a Delta-DOR measurement. TRANSMIT_FREQ_n shall provide the interferometer reference frequency. The VLBI_DELAY measurement shall be a double precision value. Units shall be seconds. 3.5.4 ANGLE DATA KEYWORDS 3.5.4.1 General Angle data is measured at the ground antenna, using downlink data only, regardless of the mode of the tracking session. There shall be two angle keywords: ANGLE_1 and ANGLE_2. The ANGLE_TYPE metadata keyword indicates how these two keywords should be interpreted. Some TDM users may require that the ANGLE_1 keyword is followed immediately by the corresponding ANGLE_2 keyword; however, this sort is not a general TDM requirement. Special sorting requirements should be specified in the ICD. 3.5.4.2 ANGLE_1 The value assigned to the ANGLE_1 keyword represents the azimuth, right ascension, or 'X' angle of the measurement, depending on the value of the ANGLE_TYPE keyword. The angle measurement shall be a double precision value as follows: -180.0 <= ANGLE_1 < 360.0. Units shall be degrees. 3.5.4.3 ANGLE_2 The value assigned to the ANGLE_2 keyword represents the elevation, declination, or 'Y' angle of the measurement, depending on the value of the ANGLE_TYPE keyword. The angle measurement shall be a double precision value as follows: -180.0 <= ANGLE_2 < 360.0. Units shall be degrees. 3.5.5 TIME RELATED KEYWORDS 3.5.5.1 CLOCK_BIAS In general, the timetags provided for the tracking data should be corrected, but when that is not possible (e.g., for three-way data or differenced data types), then this data type may be used. The CLOCK_BIAS keyword can be used by the message recipient to adjust timetag measurements by a specified amount with respect to a common reference. For example, the CLOCK_BIAS keyword may be used to show the difference between a station clock and UTC by setting PARTICIPANT_1 to 'UTC' and PARTICIPANT_2 to the name of the station clock. The observable should be calculated as clock#2 minus clock#1, consistent with the TDM convention for differenced data. This parameter may also be used to express the difference between two station clocks, for example, for differenced data including Delta-DOR. The clock bias is stated in the data, but the timetags in the message have not been corrected by applying the bias; application of the bias is up to the user of the data. Normally the time related data such as CLOCK_BIAS data and CLOCK_DRIFT data should appear in a dedicated TDM Segment, i.e., not mixed with signal data or other data types. The units for CLOCK_BIAS shall be seconds. The value shall be a double precision value, and may be positive, zero, or negative. The default value shall be 0.0. 3.5.5.2 CLOCK_DRIFT In general, ground-based clocks in tracking stations are sufficiently stable that a measurement of the clock drift may not be necessary. However, for spacecraft-to-spacecraft exchanges, there may be onboard clock drifts that are sufficiently significant that they should be accounted for in the measurements and calculations. Drift in clocks may also be an important factor when differenced data is being exchanged. The CLOCK_DRIFT keyword should be used to adjust timetag measurements by an amount that is a function of time with respect to a common reference, normally UTC (as opposed to the CLOCK_BIAS, which is meant to be a constant adjustment). Thus CLOCK_DRIFT could be used to calculate an interpolated CLOCK_BIAS between two timetags, by multiplying the CLOCK_DRIFT measurement at the timetag by the number of seconds desired and adding it to the CLOCK_BIAS. The drift should be calculated as a drift of clock#2 with respect to clock#1, consistent with the TDM convention for differenced data. Normally the time related data such as CLOCK_DRIFT data and CLOCK_BIAS data should appear in a dedicated TDM Segment, i.e., not mixed with signal data or other data types. The units for CLOCK_DRIFT shall be seconds-per-second (s/s). The value shall be a double precision value, and may be positive, zero, or negative. The default value shall be 0.0. 3.5.6 MEDIA RELATED KEYWORDS 3.5.6.1 STEC The STEC keyword (Slant Total Electron Count) shall be used to convey the line of sight, one way charged particle delay or total electron count (TEC) at the timetag associated with a tracking measurement, which is calculated by integrating the electron density along the propagation path (electrons/m2). The charged particles could have several sources, e.g., solar plasma, Earth ionosphere, or the Io plasma torus. The units for the STEC keyword are Total Electron Count Units (TECU), where 1 TECU = 1016 electrons/m2 = 1.661 x 10-8 mol/m2 (SI Units). The value shall be a positive double precision value (the TEC along the satellite line of sight may vary between 1 and 400 TECU; larger values may be observed during periods of high solar activity). This keyword should appear in its own TDM Segment with PARTICIPANTs being one spacecraft and one antenna, and a MODE setting of 'SEQUENTIAL'. Exchange partners who wish to distinguish between ionospheric and interplanetary STEC should indicate so in the ICD, and the data must be provided in separate TDM Segments. 3.5.6.2 TROPO_DRY The value associated with the TROPO_DRY keyword shall be the dry zenith delay through the troposphere measured at the timetag. There should be agreed upon elevation mappings for the dry component specified in the ICD (e.g., the Niell mapping function developed for VLBI applications). Tropospheric corrections should be applied by the recipient of the TDM; the required correction is the value associated with this keyword at the timetag. Recommended polynomial interpolations (if applicable) should be specified in the ICD. The units for TROPO_DRY shall be meters (m). The value shall be a non-negative double precision value (0.0 <= TROPO_DRY). 3.5.6.3 TROPO_WET The value associated with the TROPO_WET keyword shall be the wet zenith delay through the troposphere measured at the timetag. There should be agreed upon elevation mappings for the wet component specified in the ICD (e.g., the Niell mapping function developed for VLBI applications). Tropospheric corrections should be applied by the recipient of the TDM; the required correction is the value associated with this keyword at the timetag. Recommended polynomial interpolations (if applicable) should be specified in the ICD. The units for TROPO_WET shall be meters (m). The value shall be a non-negative double precision value (0.0 <= TROPO_WET). 3.5.7 METEOROLOGICAL RELATED KEYWORDS 3.5.7.1 PRESSURE The value associated with the PRESSURE keyword shall be the atmospheric pressure observable as measured at the tracking participant, specified in hectopascal (1 hectopascal (hPa) = 1 millibar). The PRESSURE shall be a double precision value; practically speaking it is always positive. 3.5.7.2 RHUMIDITY The value associated with the RHUMIDITY keyword shall be the relative humidity observable as measured at the tracking participant, specified in percent. RHUMIDITY shall be a double precision type value, 0 <= RHUMIDITY <= 100. 3.5.7.3 TEMPERATURE The value associated with the TEMPERATURE keyword shall be the temperature observable as measured at the tracking participant, specified in Kelvin (K). The TEMPERATURE shall be a positive double precision type value. 3.5.8 MISCELLANEOUS KEYWORDS 3.5.8.1 COMMENT The COMMENT keyword is not required. See 4.5 for full details on usage of the COMMENT keyword. 3.5.8.2 DATA_START The 'DATA_START' keyword must be the first keyword in the Data Section of the TDM Segment, which serves to delimit the Data Section. The keyword shall appear on a line by itself with no timetags or values. Example: 'DATA_START'. 3.5.8.3 DATA_STOP The 'DATA_STOP' keyword must be the last keyword in the Data Section of the TDM Segment, which serves to delimit the Data Section. The keyword shall appear on a line by itself with no timetags or values. Example: 'DATA_STOP'. 4 TRACKING DATA MESSAGE SYNTAX 4.1 GENERAL The TDM shall observe the syntax described in 4.2 through 4.5. 4.2 TDM LINES 4.2.1 The TDM shall consist of a set of TDM lines. The TDM line must contain only printable ASCII characters and blanks. ASCII control characters (such as TAB, etc.) must not be used, except as indicated below for the termination of the TDM line. A TDM line must not exceed 254 ASCII characters and spaces (excluding line termination character[s]). 4.2.2 Each TDM line shall be one of the following: - Header line; - Metadata Section line; - Data Section line; - blank line. 4.2.3 All Header, Metadata Section, and Data Section lines, with exceptions as noted below, shall use 'keyword = value' syntax, abbreviated as KVN. 4.2.4 Only a single 'keyword = value' assignment shall be made on a TDM line. 4.2.5 The following distinctions in KVN syntax shall apply for TDM lines: - TDM lines in the Header and Metadata Section shall consist of a keyword, followed by an equals sign '=', followed by a single value assignment. Before and after the equals sign, blank characters (white space) may be added, but shall not be required. - TDM lines in the Data Section shall consist of a keyword, followed by an equals sign '=', followed by a value that consists of two primary elements (essentially an ordered pair): a timetag and the measurement or calculation associated with that timetag (either without the other is unusable for tracking purposes). Before and after the equals sign, blank characters (white space) may be added. The timetag and measurement/calculation in the value must be separated by at least one blank character (white space). - The keywords COMMENT, META_START, META_STOP, DATA_START, and DATA_STOP are exceptions to the KVN syntax. 4.2.6 Keywords must be uppercase and must not contain blanks. 4.2.7 Any white space immediately preceding or following the keyword shall not be significant. 4.2.8 Any white space immediately preceding or following the equals sign '=' shall not be significant. 4.2.9 Any white space immediately preceding the end of line shall not be significant. 4.2.10 Blank lines may be used at any position within the TDM. 4.2.11 TDM lines shall be terminated by a single Carriage Return or a single Line Feed or a Carriage Return/Line Feed pair or a Line Feed/Carriage Return pair. 4.3 TDM VALUES 4.3.1 A non-empty value field must be specified for each keyword provided. 4.3.2 Integer values shall consist of a sequence of decimal digits with an optional leading sign ('+' or '-'). If the sign is omitted, '+' shall be assumed. Leading zeros may be used. The range of values that may be expressed as an integer is: -2 147 483 648 <= x <= +2 147 483 647 (i.e., -231 <= x <= 231-1). 4.3.3 Non-integer numeric values may be expressed in either fixed-point or floating-point notation. Both representations may be used within a TDM. 4.3.4 Non-integer numeric values expressed in fixed-point notation shall consist of a sequence of decimal digits separated by a period as a decimal point indicator, with an optional leading sign ('+' or '-'). If the sign is omitted, '+' shall be assumed. Leading and trailing zeros may be used. At least one digit shall be used before and after a decimal point. The number of digits shall be 16 or fewer. 4.3.5 Non-integer numeric values expressed in floating-point notation shall consist of a sign, a mantissa, an alphabetic character indicating the division between the mantissa and exponent, and an exponent, constructed according to the following rules: - The sign may be '+' or '-'. If the sign is omitted, '+' shall be assumed. - The mantissa must be a string of no more than 16 decimal digits with a decimal point '.' in the second position of the ASCII string, separating the integer portion of the mantissa from the fractional part of the mantissa. - The character used to denote exponentiation shall be 'E' or 'e'. If the character indicating the exponent and the following exponent are omitted, an exponent value of zero shall be assumed (essentially yielding a fixed-point value). - The exponent must be an integer, and may have either a '+' or '-' sign (if the sign is omitted, then '+' is assumed). - The maximum positive floating-point value is approximately 1.798E+308, with 16 significant decimal digits precision. The minimum positive floating-point value is approximately 4.94E-324, with 16 significant decimal digits precision. NOTE - These specifications for integer, fixed-point, and floating-point values conform to the XML specifications for the data types four-byte integer 'xsd:int', 'decimal', and 'double', respectively (see reference [6]). The specifications for floating-point values conform to the IEEE 754 \ double precision type (see reference [7]). Floating-point numbers in IEEE extended-single or IEEE extended-double precision may be represented, but do require an ICD between participating agencies because of their implementation specific attributes. The special values 'NaN', '-Inf', '+Inf', and '-0' are not supported in the TDM. 4.3.6 Blanks shall not be permitted within numeric values and time values. 4.3.7 Text value fields may be constructed using mixed case; case shall not be significant. 4.3.8 In value fields that are text, an underscore shall be equivalent to a single blank. Individual blanks between non-blank characters shall be retained (shall be significant) but multiple blanks shall be equivalent to a single blank. 4.3.9 In value fields that represent a timetag or epoch, one of the following two formats shall be used: YYYY-MM-DDThh:mm:ss[.d.d][Z] or YYYY-DDDThh:mm:ss[.d.d][Z] where 'YYYY' is the year, 'MM' is the two-digit month, 'DD' is the two-digit day, 'DDD' is the three-digit day of year, 'T' is constant, 'hh:mm:ss[.d.d]' is the time in hours, minutes seconds, and optional fractional seconds; 'Z' is an optional time code terminator (the only permitted value is 'Z' for Zulu, i.e., UTC). All fields shall have leading zeros. See reference [3], ASCII Time Code A and B. 4.3.10 There are four types of TDM values that represent a timetag or epoch, as shown in the applicable tables. The time system for the CREATION_DATE, START_TIME, and STOP_TIME shall be UTC. The time system for the timetags in the TDM Data Section shall be determined by the TIME_SYSTEM metadata keyword. 4.4 UNITS IN THE TDM Units are not explicitly displayed in the TDM. The units associated with values in the TDM are as specified in table 3-5. 4.5 COMMENTS IN A TDM 4.5.1 Comments may be used to provide any pertinent information associated with the data that is not covered via one of the keywords. This additional information is intended to aid in consistency checks and elaboration where needed. Comments shall not be required for successful processing of a TDM; i.e., comment lines shall be optional. NOTE - Given that TDMs may consist of large amounts of data, and are generally produced via automation, using the COMMENT feature of the TDM may have limited usefulness. On the other hand, a simple utility could be developed to search for and extract all the comments in a TDM to make them easily reviewable. Existing built-in utilities (e.g., UNIX 'grep') or 'freeware' utilities could also be used for this purpose. 4.5.2 Comment lines, if used, shall only occur: - at the beginning of the TDM Header (i.e., between the CCSDS_TDM_VERS keyword and the CREATION_DATE keyword, as shown in table 3-2); - at the beginning of the TDM Metadata Section (i.e., between the META_START keyword and the TIME_SYSTEM keyword, as shown in table 3-3); - at the beginning of the TDM Data Section (i.e., between the 'DATA_START' keyword and the first Tracking Data Record). 4.5.3 All comment lines shall begin with the 'COMMENT' keyword followed by at least one space (note: may also be preceded by spaces). The 'COMMENT' keyword must appear on every comment line, not just the first comment line. After the keyword, the remainder of the line shall be the comment value. White space shall be retained (is significant) in comment values. 4.5.4 Conventions for particular comments in the TDM that may be required between any two participating agencies should be specified in the ICD. 4.5.5 Descriptions of any ancillary data that cannot be accommodated via keywords in the TDM may have to be specified via comments, and should be outlined in the ICD. 5 SECURITY 5.1 OVERVIEW This section presents the results of an analysis of security considerations applied to the technologies specified in this Recommended Standard. 5.2 SECURITY CONCERNS RELATED TO THIS RECOMMENDED STANDARD 5.2.1 DATA PRIVACY Privacy of data formatted in compliance with the specifications of this Recommended Standard should be assured by the systems and networks on which this Recommended Standard is implemented. 5.2.2 DATA INTEGRITY Integrity of data formatted in compliance with the specifications of this Recommended Standard should be assured by the systems and networks on which this Recommended Standard is implemented. 5.2.3 AUTHENTICATION OF COMMUNICATING ENTITIES Authentication of communicating entities involved in the transport of data which complies with the specifications of this Recommended Standard should be provided by the systems and networks on which this Recommended Standard is implemented. 5.2.4 DATA TRANSFER BETWEEN COMMUNICATING ENTITIES The transfer of data formatted in compliance with this Recommended Standard between communicating entities should be accomplished via secure mechanisms approved by the IT Security functionaries of exchange participants. 5.2.5 CONTROL OF ACCESS TO RESOURCES This Recommended Standard assumes that control of access to resources will be managed by the systems upon which provider formatting and recipient processing are performed. 5.2.6 AUDITING OF RESOURCE USAGE This Recommended Standard assumes that auditing of resource usage will be handled by the management of systems and networks on which this Recommended Standard is implemented. 5.3 POTENTIAL THREATS AND ATTACK SCENARIOS There are no certain threats or attack scenarios that apply specifically to the technologies specified in this Recommended Standard. Potential threats or attack scenarios applicable to the systems and networks on which this Recommended Standard is implemented should be addressed by the management of those systems and networks. Protection from unauthorized access is especially important if the mission utilizes open ground networks such as the Internet to provide ground station connectivity for the exchange of data formatted in compliance with this Recommended Standard. 5.4 CONSEQUENCES OF NOT APPLYING SECURITY TO THE TECHNOLOGY There are no known consequences of not applying security to the technologies specified in this Recommended Standard. The consequences of not applying security to the systems and networks on which this Recommended Standard is implemented could include potential loss, corruption, and theft of data. 5.5 DATA SECURITY IMPLEMENTATION SPECIFICS Specific information-security interoperability provisions that may apply between agencies involved in an exchange of data formatted in compliance with this Recommended Standard should be specified in an ICD. ANNEX A VALUES FOR TIME_SYSTEM AND REFERENCE_FRAME (NORMATIVE) The values in this annex represent the set of acceptable values for the TIME_SYSTEM and REFERENCE_FRAME keywords. For details and description of these time systems, see reference [1]. If exchange partners wish to use different settings, they should be documented in the ICD. A1 TIME_SYSTEM METADATA KEYWORD Time System Value Meaning GMST Greenwich Mean Sidereal Time GPS Global Positioning System SCLK Spacecraft Clock (receiver) TAI International Atomic Time TCB Barycentric Coordinated Time TDB Barycentric Dynamical Time TT Terrestrial Time UT1 Universal Time UTC Coordinated Universal Time Reference Frame Value Meaning EME2000 Earth Mean Equator and Equinox of J2000 ICRF International Celestial Reference Frame ITRF2000 International Terrestrial Reference Frame 2000 ITRF-93 International Terrestrial Reference Frame 1993 ITRF-97 International Terrestrial Reference Frame 1997 TOD True of Date ANNEX B ITEMS FOR AN INTERFACE CONTROL DOCUMENT (INFORMATIVE) In several places in this document there are references to items which should be specified in an Interface Control Document (ICD) between agencies participating in an exchange of tracking data, if they are applicable to the particular exchange. The ICD should be jointly produced by both Agencies participating in a cross-support activity involving the collection, analysis, and transfer of tracking data. This section compiles those items into a single location. The greater the amount of material specified via ICD, the lesser the utility/benefit of the TDM (custom programming may be required to tailor software for each ICD). It is suggested to avoid a large number of items specified via ICD, to ensure full utility/benefit of the TDM. From an implementation standpoint, it is probable that many of the items that need to be negotiated via ICD will be introduced into the system that processes tracking data via one or more configuration files that specify the settings of specific, related parameters that will be used during the tracking session, for example, the name of the time system to be used for the tracking data. This may vary between exchange participants. Different versions of programs could be used to prepare the tracking data where these parameters differ; however, a more efficient design would be to have a single program that is configured based on tracking pass-specific information. It seems likely that there may be at least two configuration files necessary, one which contains Agency-specific parameters that do not change between tracking passes, and one which contains spacecraft/mission-specific parameters that could change with every tracking pass. Another thought on ICDs is that it might be feasible for participating agencies to have a generic baseline ICD ('standard service provider ICD') that specifies mission/spacecraftindependent entities on the interface, e.g., those associated with the agency's ground antennas (axis offsets, station locations, side motions, reference frame, epoch, supported frequency bands, etc.). Then smaller ICDs could be used for the mission/spacecraft-specific arrangements. The following table lists the items that should be covered in an ICD, along with where they are discussed in the text: See PDF version of document for table. ANNEX C ABBREVIATIONS AND ACRONYMS (INFORMATIVE) ADM Attitude Data Message ASCII American Standard Code for Information Interchange AZEL Azimuth-Elevation CCIR International Coordinating Committee for Radio Frequencies CCSDS Consultative Committee for Space Data Systems Delta-DOR Delta Differential One-Way Ranging DOR Differential One-Way Ranging DORIS Doppler Orbitography and Radiopositioning Integrated by Satellite GNSS Global Navigation Satellite System GPS Global Positioning System ICD Interface Control Document ICRF International Celestial Reference Frame IEEE Institute of Electrical and Electronics Engineers IEC International Electrotechnical Commission ISO International Organization for Standardization K Kelvin KVN Keyword = Value Notation LIDAR Light Detection and Ranging MOIMS Mission Operations and Information Management Services N/A or n/a Not Applicable / Not Available ODM Orbit Data Message OEM Orbit Ephemeris Message OPM Orbit Parameter Message Pc/No Carrier Power to Noise Spectral Density ratio Pr/No Ranging Power to Noise Spectral Density ratio PRARE Precise Range and Range Rate Equipment RADEC Right Ascension-Declination RINEX Receiver Independent Exchange RTLT Round-Trip Light Time SANA Space Assigned Numbers Authority SCLK Spacecraft Clock SFTP Secure File Transfer Protocol SLR Satellite Laser Ranging TDM Tracking Data Message TEC Total Electron Count TECU Total Electron Count Units UTC Coordinated Universal Time VLBI Very Long Baseline Interferometry XEYN X:East, Y:North XSYE X:South, Y:East XML eXtensible Markup Language ANNEX D EXAMPLE TRACKING DATA MESSAGES (INFORMATIVE) CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) COMMENT StarTrek 1-way data, Ka band down CREATION_DATE = 2005-160T20:15:00Z ORIGINATOR = NASA/JPL META_START COMMENT Data quality degraded by antenna pointing problem... COMMENT Slightly noisy dataTIME_SYSTEM = UTC PARTICIPANT_1 = DSS-25 PARTICIPANT_2 = yyyy-nnnAMODE = SEQUENTIALPATH = 2,1INTEGRATION_INTERVAL = 1 INTEGRATION_REF = MIDDLE FREQ_OFFSET = 0TRANSMIT_DELAY_1 = 0.000077 RECEIVE_DELAY_1 = 0.000077 DATA_QUALITY = DEGRADEDMETA_STOP DATA_START COMMENT TRANSMIT_FREQ_2 is spacecraft reference downlinkTRANSMIT_FREQ_2 = 2005-159T17:41:00 32023442781.733 RECEIVE_FREQ_1 = 2005-159T17:41:00 32021034790.7265 RECEIVE_FREQ_1 = 2005-159T17:41:01 32021034828.8432 RECEIVE_FREQ_1 = 2005-159T17:41:02 32021034866.9449 RECEIVE_FREQ_1 = 2005-159T17:41:03 32021034905.0327 RECEIVE_FREQ_1 = 2005-159T17:41:04 32021034943.0946 RECEIVE_FREQ_1 = 2005-159T17:41:05 32021034981.2049 RECEIVE_FREQ_1 = 2005-159T17:41:06 32021035019.2778 RECEIVE_FREQ_1 = 2005-159T17:41:07 32021035057.3773 RECEIVE_FREQ_1 = 2005-159T17:41:08 32021035095.4377 RECEIVE_FREQ_1 = 2005-159T17:41:09 32021035133.5604 RECEIVE_FREQ_1 = 2005-159T17:41:10 32021035171.5861 RECEIVE_FREQ_1 = 2005-159T17:41:11 32021035209.6653 RECEIVE_FREQ_1 = 2005-159T17:41:12 32021035247.7804 RECEIVE_FREQ_1 = 2005-159T17:41:13 32021035285.8715 RECEIVE_FREQ_1 = 2005-159T17:41:14 32021035323.8187 RECEIVE_FREQ_1 = 2005-159T17:41:15 32021035361.9571 RECEIVE_FREQ_1 = 2005-159T17:41:16 32021035400.0304 RECEIVE_FREQ_1 = 2005-159T17:41:17 32021035438.0126 RECEIVE_FREQ_1 = 2005-159T17:41:18 32021035476.1241 RECEIVE_FREQ_1 = 2005-159T17:41:19 32021035514.1714 RECEIVE_FREQ_1 = 2005-159T17:41:20 32021035552.2263 RECEIVE_FREQ_1 = 2005-159T17:41:21 32021035590.2671 RECEIVE_FREQ_1 = 2005-159T17:41:22 32021035628.304 RECEIVE_FREQ_1 = 2005-159T17:41:23 32021035666.3579 RECEIVE_FREQ_1 = 2005-159T17:41:24 32021035704.3745 RECEIVE_FREQ_1 = 2005-159T17:41:25 32021035742.4425 RECEIVE_FREQ_1 = 2005-159T17:41:26 32021035780.4974 RECEIVE_FREQ_1 = 2005-159T17:41:27 32021035818.5158 RECEIVE_FREQ_1 = 2005-159T17:41:28 32021035856.5721 RECEIVE_FREQ_1 = 2005-159T17:41:29 32021035894.5601 DATA_STOP Figure D-1: TDM Example: One-Way Data CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) COMMENT StarTrek 1-way data, Ka band down CREATION_DATE = 2005-160T20:15:00 ORIGINATOR = NASA/JPL META_START TIME_SYSTEM = UTC START_TIME = 2005-159T17:41:00 STOP_TIME = 2005-159T17:41:40 PARTICIPANT_1 = DSS-25 PARTICIPANT_2 = yyyy-nnnAMODE = SEQUENTIALPATH = 2,1INTEGRATION_INTERVAL = 1.0 INTEGRATION_REF = MIDDLE FREQ_OFFSET = 32021035200.0TRANSMIT_DELAY_1 = 0.000077 RECEIVE_DELAY_1 = 0.000077 DATA_QUALITY = RAWMETA_STOP DATA_START TRANSMIT_FREQ_2 = 2005-159T17:41:00 32023442781.733 RECEIVE_FREQ_1 = 2005-159T17:41:00 -409.2735 RECEIVE_FREQ_1 = 2005-159T17:41:01 -371.1568 RECEIVE_FREQ_1 = 2005-159T17:41:02 -333.0551 RECEIVE_FREQ_1 = 2005-159T17:41:03 -294.9673 RECEIVE_FREQ_1 = 2005-159T17:41:04 -256.9054 RECEIVE_FREQ_1 = 2005-159T17:41:05 -218.7951 RECEIVE_FREQ_1 = 2005-159T17:41:06 -180.7222 RECEIVE_FREQ_1 = 2005-159T17:41:07 -142.6227 RECEIVE_FREQ_1 = 2005-159T17:41:08 -104.5623 RECEIVE_FREQ_1 = 2005-159T17:41:09 -66.4396 RECEIVE_FREQ_1 = 2005-159T17:41:10 -28.4139 RECEIVE_FREQ_1 = 2005-159T17:41:11 9.6653 RECEIVE_FREQ_1 = 2005-159T17:41:12 47.7804 RECEIVE_FREQ_1 = 2005-159T17:41:13 85.8715 RECEIVE_FREQ_1 = 2005-159T17:41:14 123.8187 RECEIVE_FREQ_1 = 2005-159T17:41:15 161.9571 RECEIVE_FREQ_1 = 2005-159T17:41:16 200.0304 RECEIVE_FREQ_1 = 2005-159T17:41:17 238.0126 RECEIVE_FREQ_1 = 2005-159T17:41:18 276.1241 RECEIVE_FREQ_1 = 2005-159T17:41:19 314.1714 RECEIVE_FREQ_1 = 2005-159T17:41:20 352.2263 RECEIVE_FREQ_1 = 2005-159T17:41:21 390.2671 RECEIVE_FREQ_1 = 2005-159T17:41:22 428.3040 RECEIVE_FREQ_1 = 2005-159T17:41:23 466.3579 RECEIVE_FREQ_1 = 2005-159T17:41:24 504.3745 RECEIVE_FREQ_1 = 2005-159T17:41:25 542.4425 RECEIVE_FREQ_1 = 2005-159T17:41:26 580.4974 RECEIVE_FREQ_1 = 2005-159T17:41:27 618.5158 RECEIVE_FREQ_1 = 2005-159T17:41:28 656.5721 RECEIVE_FREQ_1 = 2005-159T17:41:29 694.5601 RECEIVE_FREQ_1 = 2005-159T17:41:30 732.5939 RECEIVE_FREQ_1 = 2005-159T17:41:31 770.6275 RECEIVE_FREQ_1 = 2005-159T17:41:32 808.6377 RECEIVE_FREQ_1 = 2005-159T17:41:33 846.6657 RECEIVE_FREQ_1 = 2005-159T17:41:34 884.6911 RECEIVE_FREQ_1 = 2005-159T17:41:35 922.6890 RECEIVE_FREQ_1 = 2005-159T17:41:36 960.7083 RECEIVE_FREQ_1 = 2005-159T17:41:37 998.7493 RECEIVE_FREQ_1 = 2005-159T17:41:38 1036.7388 RECEIVE_FREQ_1 = 2005-159T17:41:39 1074.7529 RECEIVE_FREQ_1 = 2005-159T17:41:40 1112.7732 DATA_STOP Figure D-2: TDM Example: One-Way Data w/Frequency Offset CCSDS_TDM_VERS=1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) CREATION_DATE=2005-184T20:15:00 ORIGINATOR=NASA/JPLMETA_START TIME_SYSTEM=UTC START_TIME=2005-184T11:12:23 STOP_TIME=2005-184T13:59:43.27 PARTICIPANT_1=DSS-55 PARTICIPANT_2=yyyy-nnnAMODE=SEQUENTIALPATH=1,2,1INTEGRATION_INTERVAL=1.0 INTEGRATION_REF=MIDDLE FREQ_OFFSET=0.0META_STOP DATA_START TRANSMIT_FREQ_1=2005-184T11:12:23 7175173383.615373 TRANSMIT_FREQ_RATE_1=2005-184T11:12:23 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:24 7175173384.017573 TRANSMIT_FREQ_RATE_1=2005-184T11:12:24 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:25 7175173384.419773 TRANSMIT_FREQ_RATE_1=2005-184T11:12:25 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:26 7175173384.821973 TRANSMIT_FREQ_RATE_1=2005-184T11:12:26 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:27 7175173385.224173 TRANSMIT_FREQ_RATE_1=2005-184T11:12:27 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:28 7175173385.626373 TRANSMIT_FREQ_RATE_1=2005-184T11:12:28 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:29 7175173386.028573 TRANSMIT_FREQ_RATE_1=2005-184T11:12:29 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:30 7175173386.430773 TRANSMIT_FREQ_RATE_1=2005-184T11:12:30 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:31 7175173386.832973 TRANSMIT_FREQ_RATE_1=2005-184T11:12:31 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:32 7175173387.235173 TRANSMIT_FREQ_RATE_1=2005-184T11:12:32 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:33 7175173387.637373 TRANSMIT_FREQ_RATE_1=2005-184T11:12:33 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:34 7175173388.039573 TRANSMIT_FREQ_RATE_1=2005-184T11:12:34 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:35 7175173388.441773 TRANSMIT_FREQ_RATE_1=2005-184T11:12:35 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:36 7175173388.843973 TRANSMIT_FREQ_RATE_1=2005-184T11:12:36 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:37 7175173389.246173 TRANSMIT_FREQ_RATE_1=2005-184T11:12:37 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:38 7175173389.648373 TRANSMIT_FREQ_RATE_1=2005-184T11:12:38 0.40220 TRANSMIT_FREQ_1=2005-184T11:12:39 7175173390.050573 RECEIVE_FREQ_1=2005-184T13:59:27.27 8429753135.986102 RECEIVE_FREQ_1=2005-184T13:59:28.27 8429749428.196568 RECEIVE_FREQ_1=2005-184T13:59:29.27 8429749427.584727 RECEIVE_FREQ_1=2005-184T13:59:30.27 8429749427.023103 RECEIVE_FREQ_1=2005-184T13:59:31.27 8429749426.346252 RECEIVE_FREQ_1=2005-184T13:59:32.27 8429749425.738658 RECEIVE_FREQ_1=2005-184T13:59:33.27 8429749425.113143 RECEIVE_FREQ_1=2005-184T13:59:34.27 8429749424.489933 RECEIVE_FREQ_1=2005-184T13:59:35.27 8429749423.876996 RECEIVE_FREQ_1=2005-184T13:59:36.27 8429749423.325228 RECEIVE_FREQ_1=2005-184T13:59:37.27 8429749422.664049 RECEIVE_FREQ_1=2005-184T13:59:38.27 8429749422.054996 RECEIVE_FREQ_1=2005-184T13:59:39.27 8429749421.425801 RECEIVE_FREQ_1=2005-184T13:59:40.27 8429749420.824186 RECEIVE_FREQ_1=2005-184T13:59:41.27 8429749420.204178 RECEIVE_FREQ_1=2005-184T13:59:42.27 8429749419.596043 RECEIVE_FREQ_1=2005-184T13:59:43.27 8429749418.986191 DATA_STOP Figure D-3: TDM Example: Two-Way Frequency Data for Doppler Calculation CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) CREATION_DATE = 2005-191T23:00:00 ORIGINATOR = NASA/JPL META_START COMMENT Range correction applied is range calibration to DSS-24. COMMENT Estimated RTLT at begin of pass = 950 secondsCOMMENT Antenna Z-height correction 0.0545 km applied to uplink signalCOMMENT Antenna Z-height correction 0.0189 km applied to downlink signalTIME_SYSTEM = UTC PARTICIPANT_1 = DSS-24 PARTICIPANT_2 = yyyy-nnnAMODE = SEQUENTIALPATH = 1,2,1 INTEGRATION_REF = START RANGE_MODE = COHERENT RANGE_MODULUS = 2.0e+26 RANGE_UNITS = RU TRANSMIT_DELAY_1 = 7.7e-5 TRANSMIT_DELAY_2 = 0.0 RECEIVE_DELAY_1 = 7.7e-5 RECEIVE_DELAY_2 = 0.0 CORRECTION_RANGE = 46.7741 CORRECTIONS_APPLIED = YES META_STOP DATA_START TRANSMIT_FREQ_1 = 2005-191T00:31:51 7180064367.3536 TRANSMIT_FREQ_RATE_1 = 2005-191T00:31:51 0.59299 RANGE = 2005-191T00:31:51 39242998.5151986 PR_N0 = 2005-191T00:31:51 28.52538 TRANSMIT_FREQ_1 = 2005-191T00:34:48 7180064472.3146 TRANSMIT_FREQ_RATE_1 = 2005-191T00:34:48 0.59305 RANGE = 2005-191T00:34:48 61172265.3115234 PR_N0 = 2005-191T00:34:48 28.39347 TRANSMIT_FREQ_1 = 2005-191T00:37:45 7180064577.2756 TRANSMIT_FREQ_RATE_1 = 2005-191T00:37:45 0.59299 RANGE = 2005-191T00:37:45 15998108.8168328 PR_N0 = 2005-191T00:37:45 28.16193 TRANSMIT_FREQ_1 = 2005-191T00:40:42 7180064682.2366 TRANSMIT_FREQ_RATE_1 = 2005-191T00:40:42 0.59299 RANGE = 2005-191T00:40:42 37938284.4138008 PR_N0 = 2005-191T00:40:42 29.44597 TRANSMIT_FREQ_1 = 2005-191T00:43:39 7180064787.1976 TRANSMIT_FREQ_RATE_1 = 2005-191T00:43:39 0.60774 RANGE = 2005-191T00:43:39 59883968.0697146 PR_N0 = 2005-191T00:43:39 27.44037 TRANSMIT_FREQ_1 = 2005-191T00:46:36 7180064894.77345 TRANSMIT_FREQ_RATE_1 = 2005-191T00:46:36 0.60989 RANGE = 2005-191T00:46:36 14726355.3958799 PR_N0 = 2005-191T00:46:36 27.30462 TRANSMIT_FREQ_1 = 2005-191T00:49:33 7180065002.72044 TRANSMIT_FREQ_RATE_1 = 2005-191T00:49:33 0.60989 RANGE = 2005-191T00:49:33 36683224.3750253 PR_N0 = 2005-191T00:49:33 28.32537 TRANSMIT_FREQ_1 = 2005-191T00:52:30 7180065110.66743 TRANSMIT_FREQ_RATE_1 = 2005-191T00:52:30 0.60983 RANGE = 2005-191T00:52:30 58645699.4734682 PR_N0 = 2005-191T00:52:30 29.06158 TRANSMIT_FREQ_1 = 2005-191T00:55:27 7180065218.61442 TRANSMIT_FREQ_RATE_1 = 2005-191T00:49:33 0.60989 RANGE = 2005-191T00:55:27 13504948.3585422 PR_N0 = 2005-191T00:55:27 27.29589 TRANSMIT_FREQ_1 = 2005-191T00:58:24 7180065326.56141 TRANSMIT_FREQ_RATE_1 = 2005-191T00:49:33 0.62085 RANGE = 2005-191T00:58:24 35478729.4012973 PR_N0 = 2005-191T00:58:24 30.48199 TRANSMIT_FREQ_1 = 2005-191T01:01:21 7180065436.45167 RANGE = 2005-191T01:01:21 57458219.0681689 PR_N0 = 2005-191T01:01:21 27.15509 DATA_STOP Figure D-4: TDM Example: Two-Way Ranging Data Only CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) CREATION_DATE = 2005-184T20:15:00 ORIGINATOR = NASA/JPL META_START TIME_SYSTEM = UTC START_TIME = 2005-184T11:12:23 STOP_TIME = 2005-184T13:59:40.27 PARTICIPANT_1 = DSS-55 PARTICIPANT_2 = yyyy-nnnAPARTICIPANT_3 = DSS-15 MODE = SEQUENTIALPATH = 1,2,3INTEGRATION_INTERVAL = 1.0 INTEGRATION_REF = MIDDLE META_STOP DATA_START TRANSMIT_FREQ_1 = 2005-184T11:12:23 7175173383.615373 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:27.27 8429753135.986102 TRANSMIT_FREQ_1 = 2005-184T11:12:24 7175173384.017573 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:28.27 8429749428.196568 TRANSMIT_FREQ_1 = 2005-184T11:12:25 7175173384.419773 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:29.27 8429749427.584727 TRANSMIT_FREQ_1 = 2005-184T11:12:26 7175173384.821973 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:30.27 8429749427.023103 TRANSMIT_FREQ_1 = 2005-184T11:12:27 7175173385.224173 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:31.27 8429749426.346252 TRANSMIT_FREQ_1 = 2005-184T11:12:28 7175173385.626373 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:32.27 8429749425.738658 TRANSMIT_FREQ_1 = 2005-184T11:12:29 7175173386.028573 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:33.27 8429749425.113143 TRANSMIT_FREQ_1 = 2005-184T11:12:30 7175173386.430773 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:34.27 8429749424.489933 TRANSMIT_FREQ_1 = 2005-184T11:12:31 7175173386.832973 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:35.27 8429749423.876996 TRANSMIT_FREQ_1 = 2005-184T11:12:32 7175173387.235173 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:36.27 8429749423.325228 TRANSMIT_FREQ_1 = 2005-184T11:12:33 7175173387.637373 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:37.27 8429749422.664049 TRANSMIT_FREQ_1 = 2005-184T11:12:34 7175173388.039573 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:38.27 8429749422.054996 TRANSMIT_FREQ_1 = 2005-184T11:12:35 7175173388.441773 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:39.27 8429749421.425801 TRANSMIT_FREQ_1 = 2005-184T11:12:36 7175173388.843973 TRANSMIT_FREQ_RATE_1 = 2005-184T11:12:23 0.40220 RECEIVE_FREQ_3 = 2005-184T13:59:40.27 8429749420.824186 DATA_STOP Figure D-5: TDM Example: Three-Way Frequency Data CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (JAXA) CREATION_DATE = 1998-06-10T01:00:00 ORIGINATOR = JAXA META_START TIME_SYSTEM = UTC START_TIME = 1998-06-10T00:57:37 STOP_TIME = 1998-06-10T00:57:44 PARTICIPANT_1 = NORTH PARTICIPANT_2 = F07R07 PARTICIPANT_3 = E7 MODE = SEQUENTIALPATH = 1,2,3,2,1INTEGRATION_INTERVAL = 1.0 INTEGRATION_REF = MIDDLE RANGE_MODE = CONSTANT RANGE_MODULUS = 0 RANGE_UNITS = km ANGLE_TYPE = AZEL META_STOP DATA_START RANGE = 1998-06-10T00:57:37 80452.7542 ANGLE_1 = 1998-06-10T00:57:37 256.64002393 ANGLE_2 = 1998-06-10T00:57:37 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:37 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:37 2287487999.0 RANGE = 1998-06-10T00:57:38 80452.7368 ANGLE_1 = 1998-06-10T00:57:38 256.64002393 ANGLE_2 = 1998-06-10T00:57:38 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:38 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:38 2287487999.0 RANGE = 1998-06-10T00:57:39 80452.7197 ANGLE_1 = 1998-06-10T00:57:39 256.64002393 ANGLE_2 = 1998-06-10T00:57:39 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:39 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:39 2287487999.0 RANGE = 1998-06-10T00:57:40 80452.7025 ANGLE_1 = 1998-06-10T00:57:40 256.64002393 ANGLE_2 = 1998-06-10T00:57:40 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:40 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:40 2287487999.0 RANGE = 1998-06-10T00:57:41 80452.6854 ANGLE_1 = 1998-06-10T00:57:41 256.64002393 ANGLE_2 = 1998-06-10T00:57:41 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:41 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:41 2287487999.0 RANGE = 1998-06-10T00:57:42 80452.6680 ANGLE_1 = 1998-06-10T00:57:42 256.64002393 ANGLE_2 = 1998-06-10T00:57:42 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:42 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:42 2287487999.0 RANGE = 1998-06-10T00:57:43 80452.6503 ANGLE_1 = 1998-06-10T00:57:43 256.64002393 ANGLE_2 = 1998-06-10T00:57:43 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:43 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:43 2287487999.0 RANGE = 1998-06-10T00:57:44 80452.6331 ANGLE_1 = 1998-06-10T00:57:44 256.64002393 ANGLE_2 = 1998-06-10T00:57:44 13.38100016 TRANSMIT_FREQ_1 = 1998-06-10T00:57:44 2106395199.07917 RECEIVE_FREQ = 1998-06-10T00:57:44 2287487999.0 DATA_STOP Figure D-6: TDM Example: Four-Way Data CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) COMMENT This example TDM describes a scenario such as might occur with a COMMENT spacecraft like Cassini, which has 3 transponders: X/S, X/X, X/Ka. COMMENT In this tracking session all 3 transponders were used. COMMENT This requires a TDM with 3 segments, because a single segment would COMMENT not be able to specify a 'PATH' statement that would describe the COMMENT S-down, X-down, and Ka-down signal paths. CREATION_DATE = 2006-347T22:51 ORIGINATOR = NASA/JPL META_START TIME_SYSTEM = UTC PARTICIPANT_1 = DSS-25 PARTICIPANT_2 = 1997-061A-X MODE = SEQUENTIAL PATH = 1,2,1 INTEGRATION_INTERVAL = 300.0 INTEGRATION_REF = MIDDLE TRANSMIT_DELAY_1 = 0.000077 RECEIVE_DELAY_1 = 0.000077 META_STOP DATA_START TRANSMIT_FREQ_1 = 2006-347T03:50:34 7175802770.23 RECEIVE_FREQ_1 = 2006-347T06:17:49 8430849716.68 DATA_STOP META_START TIME_SYSTEM = UTC PARTICIPANT_1 = DSS-25 PARTICIPANT_2 = 1997-061A-KA MODE = SEQUENTIAL PATH = 1,2,1 INTEGRATION_INTERVAL = 300.0 INTEGRATION_REF = MIDDLE TRANSMIT_DELAY_1 = 0.000077 RECEIVE_DELAY_1 = 0.000077 META_STOP DATA_START TRANSMIT_FREQ_1 = 2006-347T03:50:34 7175802770.23 RECEIVE_FREQ_1 = 2006-347T06:17:49 32037228923.40 DATA_STOP META_START TIME_SYSTEM = UTC PARTICIPANT_1 = DSS-25 PARTICIPANT_2 = 1997-061A-S PARTICIPANT_3 = DSS-24 MODE = SEQUENTIAL PATH = 1,2,3 INTEGRATION_INTERVAL = 300.0 INTEGRATION_REF = MIDDLE TRANSMIT_DELAY_1 = 7.7e-5 RECEIVE_DELAY_3 = 7.7e-5 META_STOP DATA_START TRANSMIT_FREQ_1 = 2006-347T03:50:34 7175802770.23 RECEIVE_FREQ_1 = 2006-347T06:17:49 2299322650.01 DATA_STOP Figure D-7: TDM Example: One S/C, X-up, S-down, X-down, Ka-down, Three Segments CCSDS_TDM_VERS = 1.0 CCSDS_TDM_VERS = 1.0 CREATION_DATE = 2007-08-30T12:01:44.749 ORIGINATOR = GSOC META_START TIME_SYSTEM = UTC START_TIME = 2007-08-29T07:00:02.000 STOP_TIME = 2007-08-29T14:00:02.000 PARTICIPANT_1 = HBSTK PARTICIPANT_2 = SAT MODE = SEQUENTIALPATH = 1,2,1INTEGRATION_INTERVAL = 1.0 INTEGRATION_REF = END ANGLE_TYPE = XSYE DATA_QUALITY = RAWMETA_STOP DATA_START DOPPLER_INTEGRATED = 2007-08-29T07:00:02.000 -1.498776048 ANGLE_1 = 2007-08-29T07:00:02.000 67.01312389 ANGLE_2 = 2007-08-29T07:00:02.000 18.28395556 DOPPLER_INTEGRATED = 2007-08-29T08:00:02.000 -2.201305217 ANGLE_1 = 2007-08-29T08:00:02.000 67.01982278 ANGLE_2 = 2007-08-29T08:00:02.000 21.19609167 DOPPLER_INTEGRATED = 2007-08-29T12:00:02.000 2.248620597 ANGLE_1 = 2007-08-29T12:00:02.000 -84.79697583 ANGLE_2 = 2007-08-29T12:00:02.000 4.11574444 DOPPLER_INTEGRATED = 2007-08-29T13:00:02.000 1.547592295 ANGLE_1 = 2007-08-29T13:00:02.000 -85.14762500 ANGLE_2 = 2007-08-29T13:00:02.000 4.35471389 DOPPLER_INTEGRATED = 2007-08-29T14:00:02.000 0.929545817 ANGLE_1 = 2007-08-29T14:00:02.000 -89.35626083 ANGLE_2 = 2007-08-29T14:00:02.000 2.78791667 DATA_STOP META_START TIME_SYSTEM = UTC START_TIME = 2007-08-29T06:00:02.000 STOP_TIME = 2007-08-29T13:00:02.000 PARTICIPANT_1 = WHM1 PARTICIPANT_2 = SAT MODE = SEQUENTIALPATH = 1,2,1INTEGRATION_INTERVAL = 1.0 INTEGRATION_REF = END RANGE_MODE = CONSTANT RANGE_MODULUS = 1.000000E+07 ANGLE_TYPE = AZEL DATA_QUALITY = RAWMETA_STOP DATA_START RANGE = 2007-08-29T06:00:02.000 4.00165248953670E+04 DOPPLER_INTEGRATED = 2007-08-29T06:00:02.000 -0.885640091 ANGLE_1 = 2007-08-29T06:00:02.000 99.53204250 ANGLE_2 = 2007-08-29T06:00:02.000 1.26724167 RANGE = 2007-08-29T07:00:02.000 3.57238793591890E+04 DOPPLER_INTEGRATED = 2007-08-29T07:00:02.000 -1.510223139 ANGLE_1 = 2007-08-29T07:00:02.000 103.33061750 ANGLE_2 = 2007-08-29T07:00:02.000 4.77875278 RANGE = 2007-08-29T08:00:02.000 2.90270197047210E+04 DOPPLER_INTEGRATED = 2007-08-29T08:00:02.000 -2.229907387 ANGLE_1 = 2007-08-29T08:00:02.000 104.60635806 ANGLE_2 = 2007-08-29T08:00:02.000 5.47492500 RANGE = 2007-08-29T12:00:02.000 2.81439006334980E+04 DOPPLER_INTEGRATED = 2007-08-29T12:00:02.000 2.222121620 ANGLE_1 = 2007-08-29T12:00:02.000 240.89006194 ANGLE_2 = 2007-08-29T12:00:02.000 6.71215556 RANGE = 2007-08-29T13:00:02.000 3.48156855860090E+04 DOPPLER_INTEGRATED = 2007-08-29T13:00:02.000 1.504082291 ANGLE_1 = 2007-08-29T13:00:02.000 243.73365222 ANGLE_2 = 2007-08-29T13:00:02.000 8.78254167 DATA_STOP Figure D-8: TDM Example: Angles, Range, Doppler Combined in Single TDM CCSDS_TDM_VERS = 1.0 COMMENT This TDM example contains range data timetagged at transmit time CREATION_DATE = 2005-09-17T23:59:59 ORIGINATOR = JAXA META_START TIME_SYSTEM = UTC START_TIME = 2005-09-17T00:41:38.0000 STOP_TIME = 2005-09-17T00:42:58.0000 PARTICIPANT_1 = yyyy-nnnAPARTICIPANT_2 = USC1 MODE = SEQUENTIALPATH = 2,1,2TRANSMIT_BAND = S RECEIVE_BAND = S TIMETAG_REF = TRANSMIT INTEGRATION_REF = START RANGE_MODE = CONSTANT RANGE_MODULUS = 1.0E7 RANGE_UNITS = km DATA_QUALITY = VALIDATEDCORRECTION_RANGE = 0.0 CORRECTIONS_APPLIED = YES META_STOP DATA_START RANGE = 2005-09-17T00:41:38.000000 3198.03679519614 RANGE = 2005-09-17T00:41:40.000000 3199.82505720811 RANGE = 2005-09-17T00:41:42.000000 3201.61631714467 RANGE = 2005-09-17T00:41:44.000000 3203.40832656236 RANGE = 2005-09-17T00:41:46.000000 3205.20108546120 RANGE = 2005-09-17T00:41:48.000000 3206.99384436004 RANGE = 2005-09-17T00:41:50.000000 3208.79110014575 RANGE = 2005-09-17T00:41:52.000000 3210.58535800688 RANGE = 2005-09-17T00:41:54.000000 3212.38336327374 RANGE = 2005-09-17T00:41:56.000000 3214.18136854059 RANGE = 2005-09-17T00:41:58.000000 3215.98012328859 RANGE = 2005-09-17T00:42:00.000000 3217.78037699888 RANGE = 2005-09-17T00:42:02.000000 3219.58287915260 RANGE = 2005-09-17T00:42:04.000000 3221.38613078747 RANGE = 2005-09-17T00:42:06.000000 3223.19013190349 RANGE = 2005-09-17T00:42:08.000000 3224.99488250065 RANGE = 2005-09-17T00:42:10.000000 3226.80113206010 RANGE = 2005-09-17T00:42:12.000000 3228.60963006298 RANGE = 2005-09-17T00:42:14.000000 3230.41587962244 RANGE = 2005-09-17T00:42:16.000000 3232.22587658761 RANGE = 2005-09-17T00:42:18.000000 3234.03662303393 RANGE = 2005-09-17T00:42:20.000000 3235.84886844254 RANGE = 2005-09-17T00:42:22.000000 3237.65961488886 RANGE = 2005-09-17T00:42:24.000000 3239.47560770319 RANGE = 2005-09-17T00:42:26.000000 3241.28860259295 RANGE = 2005-09-17T00:42:28.000000 3243.10384592614 RANGE = 2005-09-17T00:42:30.000000 3244.92133770276 RANGE = 2005-09-17T00:42:32.000000 3246.73882947939 RANGE = 2005-09-17T00:42:34.000000 3248.55856969945 RANGE = 2005-09-17T00:42:36.000000 3250.37681095722 RANGE = 2005-09-17T00:42:38.000000 3252.19879962071 RANGE = 2005-09-17T00:42:40.000000 3254.02003880307 RANGE = 2005-09-17T00:42:42.000000 3255.84352642885 RANGE = 2005-09-17T00:42:44.000000 3257.66851301693 RANGE = 2005-09-17T00:42:46.000000 3259.49125116157 RANGE = 2005-09-17T00:42:48.000000 3261.31848619307 RANGE = 2005-09-17T00:42:50.000000 3263.14572122459 RANGE = 2005-09-17T00:42:52.000000 3264.97295625609 RANGE = 2005-09-17T00:42:54.000000 3266.80169024990 RANGE = 2005-09-17T00:42:56.000000 3268.63267268713 RANGE = 2005-09-17T00:42:58.000000 3270.46440460551 DATA_STOP Figure D-9: TDM Example: Range Data with TIMETAG_REF=TRANSMIT CCSDS_TDM_VERS = 1.0 COMMENT This TDM example contains single differenced Doppler data. CREATION_DATE = 2006-354T01:38:00Z ORIGINATOR = NASA/JPL META_START TIME_SYSTEM = UTC START_TIME = 2003-07-08T04:45:25.0000 STOP_TIME = 2003-07-08T04:48:25.0000 PARTICIPANT_1 = yyyy-nnnAPARTICIPANT_2 = DSS-24 PARTICIPANT 3 = DSS-25 MODE = SINGLE_DIFF PATH_1 = 1,2PATH_2 = 1,3TRANSMIT_BAND = X RECEIVE_BAND = X INTEGRATION_INTERVAL = 10.0 INTEGRATION_REF = MIDDLE RECEIVE_DELAY_2 = 0.00007732 RECEIVE_DELAY_3 = 0.00007732 DATA_QUALITY = VALIDATEDMETA_STOP DATA_START COMMENT Transmit frequency is S/C beacon one OWLT prior to receive time TRANSMIT_FREQ_1 = 2003-07-08T04:10:0000 8.435360E+09 RECEIVE_FREQ = 2003-07-08T04:45:25.0000 8.738750457763670E+00 RECEIVE_FREQ = 2003-07-08T04:45:35.0000 8.320683479309080E+00 RECEIVE_FREQ = 2003-07-08T04:45:45.0000 7.909399032592770E+00 RECEIVE_FREQ = 2003-07-08T04:45:55.0000 7.490205764770500E+00 RECEIVE_FREQ = 2003-07-08T04:46:05.0000 7.149572372436510E+00 RECEIVE_FREQ = 2003-07-08T04:46:15.0000 6.808938980102530E+00 RECEIVE_FREQ = 2003-07-08T04:46:25.0000 6.481011390686030E+00 RECEIVE_FREQ = 2003-07-08T04:46:35.0000 6.167441368103020E+00 RECEIVE_FREQ = 2003-07-08T04:46:45.0000 5.865190505981440E+00 RECEIVE_FREQ = 2003-07-08T04:46:55.0000 5.590643882751460E+00 RECEIVE_FREQ = 2003-07-08T04:47:05.0000 5.330531120300290E+00 RECEIVE_FREQ = 2003-07-08T04:47:15.0000 5.083267211914060E+00 RECEIVE_FREQ = 2003-07-08T04:47:25.0000 4.850607872009270E+00 RECEIVE_FREQ = 2003-07-08T04:47:35.0000 4.643701979796000E+00 RECEIVE_FREQ = 2003-07-08T04:47:45.0000 4.453802272725000E+00 RECEIVE_FREQ = 2003-07-08T04:47:55.0000 4.281702585856000E+00 RECEIVE_FREQ = 2003-07-08T04:48:05.0000 4.127402919189000E+00 RECEIVE_FREQ = 2003-07-08T04:48:15.0000 3.990903272724000E+00 RECEIVE_FREQ = 2003-07-08T04:48:25.0000 3.872203646461000E+00 DATA_STOP Figure D-10: TDM Example: Differenced Doppler Observable CCSDS_TDM_VERS = 1.0 COMMENT This TDM example contains Delta-DOR data. COMMENT Quasar CTD 20 also known as J023752.4+284808 (ICRF), 0234+285 (IERS) CREATION_DATE = 2005-178T21:45:00 ORIGINATOR = NASA/JPLMETA_START TIME_SYSTEM = UTC START_TIME = 2004-136T15:42:00.0000 STOP_TIME = 2004-136T16:02:00.0000 PARTICIPANT_1 = VOYAGER1 PARTICIPANT_2 = DSS-55 PARTICIPANT_3 = DSS-25 MODE = SINGLE_DIFF PATH_1 = 1,2PATH_2 = 1,3TRANSMIT_BAND = X RECEIVE_BAND = X TIMETAG_REF = RECEIVE RANGE_MODE = ONE_WAY RANGE_MODULUS = 1.674852710000000E+02 RECEIVE_DELAY_3 = 0.000077 DATA_QUALITY = VALIDATEDMETA_STOP DATA_START COMMENT Timetag is time of signal arrival at PARTICIPANT_2. COMMENT Transmit frequency is spacecraft beacon a OWLT before receive time. DOR = 2004-136T15:42:00.0000 -4.911896106591159E-03 DOR = 2004-136T16:02:00.0000 1.467382930436399E-02 TRANSMIT_FREQ_1 = 2004-136T14:42:00.0000 8.415123456E+09DATA_STOP META_START TIME_SYSTEM = UTC START_TIME = 2004-136T15:52:00.0000 STOP_TIME = 2004-136T15:52:00.0000 PARTICIPANT_1 = CTD 20 PARTICIPANT_2 = DSS-55 PARTICIPANT_3 = DSS-25 MODE = SINGLE_DIFF PATH_1 = 1,2PATH_2 = 1,3TRANSMIT_BAND = X RECEIVE_BAND = X TIMETAG_REF = RECEIVE RANGE_MODE = ONE_WAY RANGE_MODULUS = 1.674852710000000E+02 RECEIVE_DELAY_3 = 0.000077 DATA_QUALITY = VALIDATEDMETA_STOP DATA_START COMMENT Timetag is time of signal arrival at PARTICIPANT_2. COMMENT Transmit frequency is reference for 2-station interferometer. VLBI_DELAY = 2004-136T15:52:00.0000 -1.911896106591159E-03 TRANSMIT_FREQ_1 = 2004-136T15:42:00.0000 8.415123000E+09DATA_STOP META_START TIME_SYSTEM = UTC PARTICIPANT_1 = DSS-55 PARTICIPANT_2 = DSS-25 DATA_QUALITY = VALIDATEDMETA_STOP DATA_START CLOCK_BIAS = 2004-136T15:42:00.0000 -4.59e-7 CLOCK_BIAS = 2004-136T16:02:00.0000 -4.59e-7 DATA_STOP Figure D-11: TDM Example: Delta-DOR Observable CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) COMMENT StarTrek: one minute of launch angles from DSS-16 CREATION_DATE = 2005-157T18:25:00 ORIGINATOR = NASA/JPLMETA_START TIME_SYSTEM = UTC START_TIME = 2004-216T07:44:00 STOP_TIME = 2004-216T07:45:00 PARTICIPANT_1 = DSS-16 PARTICIPANT_2 = yyyy-nnnAMODE = SEQUENTIALPATH = 2,1ANGLE_TYPE = XSYE CORRECTION_ANGLE_1 = -0.09 CORRECTION_ANGLE_2 = 0.18 CORRECTIONS_APPLIED = NO META_STOP DATA_START ANGLE_1 = 2004-216T07:44:00 -23.62012 ANGLE_2 = 2004-216T07:44:00 -73.11035 ANGLE_1 = 2004-216T07:44:10 -23.04004 ANGLE_2 = 2004-216T07:44:10 -72.74316 ANGLE_1 = 2004-216T07:44:20 -22.78125 ANGLE_2 = 2004-216T07:44:20 -72.53027 ANGLE_1 = 2004-216T07:44:30 -22.59180 ANGLE_2 = 2004-216T07:44:30 -72.37598 ANGLE_1 = 2004-216T07:44:40 -22.40527 ANGLE_2 = 2004-216T07:44:40 -72.23730 ANGLE_1 = 2004-216T07:44:50 -22.23047 ANGLE_2 = 2004-216T07:44:50 -72.08887 ANGLE_1 = 2004-216T07:45:00 -22.08984 ANGLE_2 = 2004-216T07:45:00 -71.93750 DATA_STOP Figure D-12: TDM Example: Angle Data Only CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by NASA/JPL Navigation System Engineering CREATION_DATE = 2005-282T23:00:00 ORIGINATOR = NASA/JPL META_START TIME_SYSTEM = UTC START_TIME = 2005-274T12:00:00 STOP_TIME = 2005-280T12:00:00 PARTICIPANT_1 = DSS-14 DATA_QUALITY = VALIDATEDMETA_STOP DATA_START COMMENT Elevation mapping function is Niell modelTROPO_DRY = 2005-274T12:00:00 2.0526 TROPO_DRY = 2005-275T12:00:00 2.0530 TROPO_DRY = 2005-276T12:00:00 2.0533 TROPO_DRY = 2005-277T12:00:00 2.0537 TROPO_DRY = 2005-278T12:00:00 2.0540 TROPO_DRY = 2005-279T12:00:00 2.0544 TROPO_DRY = 2005-280T12:00:00 2.0547 TROPO_WET = 2005-274T12:00:00 0.1139 TROPO_WET = 2005-275T12:00:00 0.1126 TROPO_WET = 2005-276T12:00:00 0.1113 TROPO_WET = 2005-277T12:00:00 0.1099 TROPO_WET = 2005-278T12:00:00 0.1086 TROPO_WET = 2005-279T12:00:00 0.1074 TROPO_WET = 2005-280T12:00:00 0.1061 DATA_STOP META_START COMMENT Line of vertical ionospheric calibration for yyyy-nnnACOMMENT Time tags are end time of 15 minute measurement intervalTIME_SYSTEM = UTC START_TIME = 2005-280T21:45:00 STOP_TIME = 2005-281T00:00:00 PARTICIPANT_1 = DSS-14 PARTICIPANT_2 = yyyy-nnnAMODE = SEQUENTIALPATH = 2, 1DATA_QUALITY = VALIDATEDMETA_STOP DATA_START STEC = 2005-280T21:45:00 23.1 STEC = 2005-280T22:00:00 22.8 STEC = 2005-280T22:15:00 23.2 STEC = 2005-280T22:30:00 24.4 STEC = 2005-280T22:45:00 23.6 STEC = 2005-280T23:00:00 22.4 STEC = 2005-280T23:15:00 22.6 STEC = 2005-280T23:30:00 24.6 STEC = 2005-280T23:45:00 24.0 STEC = 2005-281T00:00:00 22.2 DATA_STOP Figure D-13: TDM Example: Media Data Only CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) COMMENT JPL/DSN/Goldstone (DSS-10) weather for DOY 156, 2005 CREATION_DATE = 2005-156T06:15:00 ORIGINATOR = NASA/JPLMETA_START TIME_SYSTEM = UTC START_TIME = 2005-156T00:03:00 STOP_TIME = 2005-156T06:03:00 PARTICIPANT_1 = DSS-10 DATA_QUALITY = VALIDATEDMETA_STOP DATA_START TEMPERATURE = 2005-156T00:03:00 302.95 PRESSURE = 2005-156T00:03:00 896.2 RHUMIDITY = 2005-156T00:03:00 12.0 TEMPERATURE = 2005-156T00:33:00 304.05 PRESSURE = 2005-156T00:33:00 895.9 RHUMIDITY = 2005-156T00:33:00 11.0 TEMPERATURE = 2005-156T01:03:00 302.55 PRESSURE = 2005-156T01:03:00 895.7 RHUMIDITY = 2005-156T01:03:00 12.0 TEMPERATURE = 2005-156T01:33:00 302.65 PRESSURE = 2005-156T01:33:00 895.7 RHUMIDITY = 2005-156T01:33:00 11.0 TEMPERATURE = 2005-156T02:03:00 301.55 PRESSURE = 2005-156T02:03:00 895.9 RHUMIDITY = 2005-156T02:03:00 11.0 TEMPERATURE = 2005-156T02:33:00 300.45 PRESSURE = 2005-156T02:33:00 895.9 RHUMIDITY = 2005-156T02:33:00 12.0 TEMPERATURE = 2005-156T03:03:00 299.55 PRESSURE = 2005-156T03:03:00 896.1 RHUMIDITY = 2005-156T03:03:00 14.0 TEMPERATURE = 2005-156T03:33:00 298.65 PRESSURE = 2005-156T03:33:00 896.2 RHUMIDITY = 2005-156T03:33:00 15.0 TEMPERATURE = 2005-156T04:03:00 298.05 PRESSURE = 2005-156T04:03:00 896.4 RHUMIDITY = 2005-156T04:03:00 17.0 TEMPERATURE = 2005-156T04:33:00 297.15 PRESSURE = 2005-156T04:33:00 896.8 RHUMIDITY = 2005-156T04:33:00 19.0 TEMPERATURE = 2005-156T05:03:00 294.85 PRESSURE = 2005-156T05:03:00 897.3 RHUMIDITY = 2005-156T05:03:00 21.0 TEMPERATURE = 2005-156T05:33:00 293.95 PRESSURE = 2005-156T05:33:00 897.3 RHUMIDITY = 2005-156T05:33:00 23.0 TEMPERATURE = 2005-156T06:03:00 293.05 PRESSURE = 2005-156T06:03:00 897.3 RHUMIDITY = 2005-156T06:03:00 25.0 DATA_STOP Figure D-14: TDM Example: Meteorological Data Only CCSDS_TDM_VERS = 1.0 COMMENT TDM example created by yyyyy-nnnA Nav Team (NASA/JPL) COMMENT The following are clock offsets, in seconds between theCOMMENT clocks at each DSN complex relative to UTC(NIST). The offset COMMENT is a mean of readings using several GPS space vehicles inCOMMENT common view. Value is "station clock minus UTC". CREATION_DATE = 2005-161T15:45:00 ORIGINATOR = NASA/JPL META_START COMMENT Note: SPC10 switched back to Maser1 from Maser2 on 2005-142 TIME_SYSTEM = UTC START_TIME = 2005-142T12:00:00 STOP_TIME = 2005-145T12:00:00 PARTICIPANT_1 = UTC-NIST PARTICIPANT_2 = DSS-10 META_STOP DATA_START CLOCK_BIAS = 2005-142T12:00:00 9.56e-7 CLOCK_DRIFT = 2005-142T12:00:00 6.944e-14 CLOCK_BIAS = 2005-143T12:00:00 9.62e-7 CLOCK_DRIFT = 2005-143T12:00:00 -2.083e-13 CLOCK_BIAS = 2005-144T12:00:00 9.44e-7 CLOCK_DRIFT = 2005-144T12:00:00 -2.778e-13 CLOCK_BIAS = 2005-145T12:00:00 9.20e-7 DATA_STOP META_START TIME_SYSTEM = UTC START_TIME = 2005-142T12:00:00 STOP_TIME = 2005-145T12:00:00 PARTICIPANT_1 = UTC-NIST PARTICIPANT_2 = DSS-40 META_STOP DATA_START CLOCK_BIAS = 2005-142T12:00:00 -7.40e-7 CLOCK_DRIFT = 2005-142T12:00:00 -3.125e-13 CLOCK_BIAS = 2005-143T12:00:00 -7.67e-7 CLOCK_DRIFT = 2005-143T12:00:00 -1.620e-13 CLOCK_BIAS = 2005-144T12:00:00 -7.81e-7 CLOCK_DRIFT = 2005-144T12:00:00 -4.745e-13 CLOCK_BIAS = 2005-145T12:00:00 -8.22e-7 DATA_STOP META_START TIME_SYSTEM = UTC START_TIME = 2005-142T12:00:00 STOP_TIME = 2005-145T12:00:00 PARTICIPANT_1 = UTC-NIST PARTICIPANT_2 = DSS-60 META_STOP DATA_START CLOCK_BIAS = 2005-142T12:00:00 -1.782e-6 CLOCK_DRIFT = 2005-142T12:00:00 1.736e-13 CLOCK_BIAS = 2005-143T12:00:00 -1.767e-6 CLOCK_DRIFT = 2005-143T12:00:00 1.157e-14 CLOCK_BIAS = 2005-144T12:00:00 -1.766e-6 CLOCK_DRIFT = 2005-144T12:00:00 8.102e-14 CLOCK_BIAS = 2005-145T12:00:00 -1.759e-6 DATA_STOP Figure D-15: TDM Example: Clock Bias/Drift Only The following are some additional scenarios that are not currently considered in the example set, but could be included in later versions of the TDM: a) S/C-S/C crosslinks; b) Ground based transponder; c) 'DORIS'; d) Arrayed downlink; e) Orbital debris example; f) Combination of radiometric types with media or meteorological data. ANNEX E INFORMATIVE REFERENCES (INFORMATIVE) NOTE - Normative references are provided in 1.5. [E1] Standard Frequencies and Time Signals. Volume 7 of Recommendations and Reports of the CCIR: XVIIth Plenary Assembly. Geneva: CCIR, 1990. [E2] Radio Metric and Orbit Data. Recommendation for Space Data System Standards, CCSDS 501.0-B-1-S. Historical Recommendation. Issue 1-S. Washington, D.C.: CCSDS, January 1987. [E3] Catherine L. Thornton and James S. Border. Radiometric Tracking Techniques for Deep-Space Navigation. JPL Deep Space Communications and Navigation Series. Hoboken, New Jersey: Wiley, February 2003. [E4] Theodore D. Moyer. Formulation for Observed and Computed Values of Deep Space Network Data Types for Navigation. JPL Deep Space Communications and Navigation Series. Hoboken, New Jersey: Wiley, January 2003. [E5] Procedures Manual for the Consultative Committee for Space Data Systems. CCSDS A00.0-Y-9. Yellow Book. Issue 9. Washington, D.C.: CCSDS, November 2003. [E6] The Application of CCSDS Protocols to Secure Systems. Report Concerning Space Data System Standards, CCSDS 350.0-G-2. Green Book. Issue 2. Washington, D.C.: CCSDS, January 2006. [E7] Attitude Data Messages. Draft Recommendation for Space Data System Standards, CCSDS 504.0-R-1. Red Book. Issue 1. Washington, D.C.: CCSDS, November 2005. [E8] XML Specification for Navigation Data Messages. Draft Recommendation for Space Data System Standards, CCSDS 505.0-R-1. Red Book. Issue 1. Washington, D.C.: CCSDS, November 2005. ANNEX F RATIONALE FOR TRACKING DATA MESSAGES (INFORMATIVE) F1 GENERAL This annex presents the rationale behind the design of the Tracking Data Message. It may help the application engineer construct a suitable message. Corrections and/or additions to these requirements may occur during future updates. A specification of requirements agreed to by all parties is essential to focus design and to ensure the product meets the needs of the Member Agencies. There are many ways of organizing requirements, but the categorization of requirements is not as important as the agreement to a sufficiently comprehensive set. In this section, the requirements are organized into three categories: Primary Requirements - These are the most elementary and necessary requirements. They would exist no matter the context in which the CCSDS is operating, i.e., regardless of preexisting conditions within the CCSDS or its Member Agencies. Heritage Requirements - These are additional requirements that derive from pre-existing Member Agency requirements, conditions, or needs. Ultimately these carry the same weight as the Primary Requirements. This Recommended Standard reflects heritage requirements pertaining to some of the technical participants' home institutions collected during the preparation of the Recommended Standard; it does not speculate on heritage requirements that could arise from other Member Agencies. Desirable Characteristics - These are not requirements, but they are felt to be important or useful features of the Recommended Standard. F2 PRIMARY REQUIREMENTS ACCEPTED FOR TRACKING DATA MESSAGES Table F-1: Primary Requirements See PDF version of document for table. Table F-2: Heritage Requirements See PDF version of document for table. Table F-3: Desirable Characteristics See PDF version of document for table. TDM SUMMARY SHEET (INFORMATIVE) The tables in the following pages of this annex show the association between data types and metadata keywords. There are only a few required metadata keywords, but many more that are applicable to one or more of the various data types. Additionally, there are some keywords that are only applicable in certain restricted situations. Finally, there are some metadata keywords that are completely optional. This summary may assist the user in constructing a TDM that captures the data from a specific measurement session. See PDF version of document for tables.